In this paper, a structural design and controller optimization process for a five-bar planar manipulator are studied using three different population-based optimization techniques: particle swarm optimization, genetic algorithm, and differential evolution. First, the desired kinematic properties of the manipulator, such as the position, velocity, and acceleration of the endpoint, are determined using inverse kinematics. Then, an optimization problem is created to minimize the shaking force and moments, and the desired kinematic quantities are implemented as constraints. All the link properties of the manipulator are defined as design variables, and the optimization results are obtained. The results show that it is possible to significantly reduce the shaking force and moment significantly thanks to the optimal design parameters. Finally, the controller is optimized to find the best PID gains considering the forward kinematics of the manipulator. It is observed that the shaking force and shaking moment can be reduced by 99% and 54%, respectively, which has a very positive effect on the accuracy of the trajectory tracking. Moreover, the performances of the optimization methods are compared by using the same number of iterations in the calculations, and thus, it can be seen that the GA method achieves the best results compared to the others. Therefore, the results of this study are of utmost importance for a manufacturer, who wants to design a five-bar planar manipulator and its controller.
This study explores the sliding mode control (SMC) strategy to address challenges such as nonlinear dynamics, steady-state errors, and torque fluctuations in elastic cable-driven winch systems. While traditional Proportional-Derivative (PD) control is sufficient for linear systems, it struggles with instability and accuracy issues in flexible systems. SMC provides robustness against uncertainties but can cause mechanical wear and performance degradation due to its chattering effect. To mitigate this, a continuous control signal-based SMC approach was adopted, reducing chattering and improving system stability. This study focuses on tracking and position control, as well as managing motor torque fluctuations during position control, emphasizing controller parameter optimization. Experimental results demonstrate that SMC outperforms PD control in tracking, position control, and torque management.
This paper presents a hardware-in-the-loop (HIL) simulation case study on the application of High-Order Sliding Mode Control (HOSMC) to a flexible-link robotic arm. The developed HIL platform combines physical hardware components with a simulated plant model, enabling real-time testing of control algorithms under realistic operating conditions without requiring a full-scale prototype. HOSMC, an advanced nonlinear control strategy, mitigates the chattering effects inherent in conventional sliding mode control by driving the system to a reduced-order sliding manifold within a finite time, resulting in smoother actuator commands and reduced mechanical stress. Flexible-link arms, while lightweight and energy-efficient, are inherently nonlinear and prone to vibration, posing significant control challenges. In this case study, the experimental HIL environment is used to evaluate HOSMC performance, demonstrating improved trajectory tracking, reduced overshoot, and minimized steady-state error. The results confirm that HIL simulation offers an effective bridge between theoretical control design and practical implementation for advanced robotic systems.
30 September 2026 in Turkish Journal of Science and Technology
In cable-driven mechanisms, cable elasticity degrades linear controller performance, causing oscillations and reducing positioning accuracy. The main novelty of this study is the real-time experimental application of a nonlinear PID (NPID) controller based on the fal function to effectively suppress these oscillations in an elastic cable winch system. The fal function enables dynamic gain adaptation based on error magnitude. The experimental setup was driven by a dSPACE DS1104 board with a sampling time of 0.001 s, utilizing a five-cycle periodic trapezoidal reference to evaluate all operating conditions in a single run. Compared to a conventional PID tuned under identical hardware conditions, the proposed NPID reduced the maximum absolute error by 57%, accumulated error by 42%, average error amplitude by 40%, and total control effort by 26%. Ultimately, the NPID significantly improves tracking accuracy and actuator efficiency in flexible electromechanical systems without deviating from the familiar PID structure.
25 October 2026 in Firat University Journal of Experimental and Computational Engineering
This study presents real-time vertical position tracking of an elastic cable winch system using a fuzzy logic-based PD (FLC-PD) controller. The dynamic model of the system was used with a two-degree-of-freedom reduced form derived from a four-degree-of-freedom structure in the previous work; drum angle and load position were taken as state variables. The FLC-PD controller was designed in MATLAB/Simulink and executed in real time on the dSPACE DS1104 platform. A square wave signal was chosen as the reference trajectory. This signal allows observation of transient and steady-state behaviors of the system within the same experiment. The experiments aimed to achieve the best transient and steady-state performance while minimizing energy consumption. While the closed-loop system with a classic PD controller provided a fast response, it exhibited 19% overshoot and steady-state oscillations. On the other hand, the closed-loop system with the FLC-PD controller reduced the overshoot to 7%, achieved the lowest steady-state error with a value of 2.285 mm, and consumed the least control energy with a value of 2.418. According to the results, FLC-PD outperformed classical PD in both reference tracking and energy consumption. This result demonstrates that FLC-PD offers an energy-efficient, feasible control solution for nonlinear winch systems where cable elasticity is dominant.