Michaela Topinková

Dr. Michaela Topinková

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 August 2022 in Materials
Verified
Journal Article
Open access
PDF file
HOHana Ovčačíková
Hana Ovčačíková
MVMarek Velicka
Marek Velicka
JVJozef Vlček
Jozef Vlček
MTMichaela Topinková
Michaela Topinková
MKMiroslava Klárová
Miroslava Klárová
JBJiří Burda
Jiří Burda
In terms of its chemical composition, biomass is a very complex type of fuel. Its combustion leads to the formation of materials such as alkaline ash and gases, and there is evidence of the corrosive effect this process has on refractory linings, thus shortening the service life of the combustion unit. This frequently encountered process is known as “alkaline oxidative bursting”. Corrosion is very complex, and it has not been completely described yet. Alkaline corrosion is the most common cause of furnace-lining degradation in aggregates that burn biomass. This article deals with an experiment investigating the corrosion resistance of 2 types of refractory materials in the Al2O3-SiO2 binary system, for the following compositions: I. (53 wt.% SiO2/42 wt.% Al2O3) and II. (28 wt.% SiO2/46 wt.% Al2O3/12 wt.% SiC). These were exposed to seven types of ash obtained from one biomass combustion company in the Czech Republic. The chemical composition of the ash is a good indicator of the problematic nature of a type of biomass. The ashes were analyzed by X-ray diffraction and X-ray fluorescence. Analysis confirmed that ash composition varies. The experiment also included the calculation of the so-called “slagging/fouling index” (I/C, TA, Sr, B/A, Fu, etc.), which can be used to estimate the probability of slag formation in combustion units. The corrosive effect on refractory materials was evaluated according to the norm ČSN P CEN/TS 15418, and a static corrosion test was used to investigate sample corrosion.

23 October 2022 in Minerals
Verified
Journal Article
Open access
PDF file
MVMarta Valášková
Marta Valášková
ZKZdeněk Klika
Zdeněk Klika
JVJozef Vlček
Jozef Vlček
LMLenka Matějová
Lenka Matějová
MTMichaela Topinková
Michaela Topinková
JMJana Madejova
Jana Madejova
The reaction products resulting from the alkali-activation of metakaolin are impacted by the composition of the initial kaolin, and amount of alkali-activated kaolinite and water. The present study focused on analyzing these parameters on the metakaolins calcined at 800 °C from three kaolins, and the metakaolins’ alkali activation for 2, 3 and 28 days. The first objective was to evaluate the mineral chemistry and quantitative mineral phase composition from the bulk chemical analysis using the chemical quantitative mineral analysis (CQMA) procedure and conduct a comparison of the chemistry of the metakaolins after alkali activation for 28 days according to the elements Al, Si, Na and K, using the leaching test in distilled water. The second task was to search for possible relationships between the quantitative number of phases in alkali-activated metakaolins and compressive strength. The main methods used for the characterization of material were X-ray fluorescence, X-ray diffraction, thermal TG/DTA and infrared spectroscopy. Metakaolins alkali activated for 28 days contained crystalline quartz, muscovite, orthoclase, and unreacted metakaolinite contained zeolite A (Z-A), hydrosodalite (HS) and thermonatrite (TN) in the amorphous/weakly crystalline phase. The compressive strengths (CS) from 6.42 ± 0.33 to 9.97 ± 0.50 MPa are related positively to H2O+ and H2O bound in HS and TN.

3 March 2023 in Minerals
Verified
Journal Article
Open access
PDF file
JVJozef Vlček
Jozef Vlček
HOHana Ovčačíková
Hana Ovčačíková
MVMarek Velicka
Marek Velicka
MTMichaela Topinková
Michaela Topinková
JBJiří Burda
Jiří Burda
PMPetra Matějková
Petra Matějková
The main problem affecting the life of refractory linings in furnaces is alkaline corrosion formed during biomass combustion, especially in systems with SiO2–Al2O3. This corrosion effect is very intensive compared to using conventional technologies designed for burning traditional fuels. This study focuses on the development of a new type of andalusite refractory material with a higher corrosion resistance to K2CO3 and fly ash after biomass combustion. The original andalusite refractory material is labeled A60PT0, with an oxide content of 60 wt.% Al2O3 and 37 wt.% SiO2, a compressive strength parameter of 64 MPa, and an apparent porosity of 15%. In the experiment, four mixtures (labeled A60PT1–A60PT4) were modified primarily using the raw materials and granulometry. The fly ash was characterized by an X-ray diffraction analysis with the following phases: quartz, calcite, microcline, leucite, portlandite, and hematite. According to the X-ray fluorescence analysis, the samples contained the following oxides: 47 wt.% CaO, 12 wt.% K2O, 4.6 wt.% SiO2, 3.5 wt.% MgO, and some minority oxides such as P2O5, MgO, MnO, and Fe2O3 between 2 and 5 %. The tendency for slagging/fouling of the ash was determined with the help of the indexes B/A, TA, Kt, and Fu. The final material was a shaped andalusite refractory material labeled A60PT4 with a content of 65 wt.% Al2O3 and 36 wt.% SiO2. The properties of the andalusite material were a compressive strength of 106.9 MPa, an apparent porosity of 13%, and the recommended temperature of use up to 1300 °C. For corrosion testing, a static crucible test was performed according to the norm ČSN CEN/TS 15418 and the company’s internal regulation. The exposure time of the samples was 2 h and 5 h at temperatures of 1100 °C and 1400 °C for K2CO3 and ash, respectively. For the evaluation of tested samples, an X-ray powder differential analysis, an X-ray fluorescence analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were used.

13 February 2021 in Minerals
Verified
Journal Article
Open access
PDF file
JVJozef Vlček
Jozef Vlček
MTMichaela Topinková
Michaela Topinková
MKMiroslava Klárová
Miroslava Klárová
PMPetra Maierová
Petra Maierová
HOHana Ovčačíková
Hana Ovčačíková
VBVeronika Blahůšková
Veronika Blahůšková
Metakaolin (MK) prepared by the calcination of kaolin at 550 °C and fly ash (FA) from the combustion of black coal in a granulating boiler were used to prepare unfired ceramic bonding systems via the alkali activation process. A long-term stability of the mechanical properties of the prepared samples similar to the unfired ceramic systems was observed. The optimal metakaolin and fly ash ratio, the type of the activator (NaOH or water glass) and its concentration were evaluated after the hydration in: a) laboratory conditions; b) hydration box; and c) under the hydrothermal activation. Raw materials and the samples prepared by alkali activation process were characterized by XRD, XRF, TG/DTA, and FTIR methods. The mechanical properties of the prepared samples were tested using a compressive strength test after 2, 28 and 56 days of hydration. The compressive strengths of 16 and 24 MPa after 28 days of hydration were reached for FA samples activated with water glass. The alkali activation of MK was successful in the NaOH solution of the molar concentration above 5 M. The compressive strength values of metakaolin, activated hydrothermally and hydrated at laboratory conditions, reached 11.2 and 5.5 MPa, respectively, for 5 M activator of NaOH.

23 December 2025 in Ceramics International
Verified
Journal Article
Open access
HOHana Ovčačíková
Hana Ovčačíková
MTMichaela Topinková
Michaela Topinková
JFJiří Fiedor
Jiří Fiedor
JTJonáš Tokarský
Jonáš Tokarský
JRJiří Rozbroj
Jiří Rozbroj
PZPiotr Zubek
Piotr Zubek

21 October 2021 in Minerals
Verified
Journal Article
Open access
PDF file
MKMiroslava Klárová
Miroslava Klárová
JVJozef Vlček
Jozef Vlček
MTMichaela Topinková
Michaela Topinková
JBJiří Burda
Jiří Burda
AMAlexandr Martaus
Alexandr Martaus
Jacek SzczerbaJacek Szczerba
Jacek Szczerba
An alternative binder to calcium aluminate cement (CAC) was prepared by the sol-gel method. Chemically pure systems such as tetraethylorthosilicate (SiC8H20O4) and nonahydrate of alumina nitrate (Al(NO3)3·9H2O) were used as major raw materials. The manufacturing process of binder via solution is mentioned, and transitions in binder structure as a function of thermal treatment in the range between 85 and 1400 °C are described. Finally, binder efficiency was verified by its application in high-temperature concrete instead of calcium aluminate cement (CAC). Newly developed sol-gel binder was characterized by XRFS quantitative analyses, XRD diffraction, STA-DTA and TG analyses and the BET method. Samples of concrete which were based on natural bauxite raw material showed cold compressive strength of 42 MPa compared to the same material where a conventional CAC was applied, and samples reached cold compressive strength of 44 MPa.