Petra Matějková

Dr. Petra Matějková

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 March 2023 in Minerals
Verified
Journal Article
Open access
PDF file
JVJozef Vlček
Jozef Vlček
HOHana Ovčačíková
Hana Ovčačíková
MVMarek Velicka
Marek Velicka
MTMichaela Topinková
Michaela Topinková
JBJiří Burda
Jiří Burda
PMPetra Matějková
Petra Matějková
The main problem affecting the life of refractory linings in furnaces is alkaline corrosion formed during biomass combustion, especially in systems with SiO2–Al2O3. This corrosion effect is very intensive compared to using conventional technologies designed for burning traditional fuels. This study focuses on the development of a new type of andalusite refractory material with a higher corrosion resistance to K2CO3 and fly ash after biomass combustion. The original andalusite refractory material is labeled A60PT0, with an oxide content of 60 wt.% Al2O3 and 37 wt.% SiO2, a compressive strength parameter of 64 MPa, and an apparent porosity of 15%. In the experiment, four mixtures (labeled A60PT1–A60PT4) were modified primarily using the raw materials and granulometry. The fly ash was characterized by an X-ray diffraction analysis with the following phases: quartz, calcite, microcline, leucite, portlandite, and hematite. According to the X-ray fluorescence analysis, the samples contained the following oxides: 47 wt.% CaO, 12 wt.% K2O, 4.6 wt.% SiO2, 3.5 wt.% MgO, and some minority oxides such as P2O5, MgO, MnO, and Fe2O3 between 2 and 5 %. The tendency for slagging/fouling of the ash was determined with the help of the indexes B/A, TA, Kt, and Fu. The final material was a shaped andalusite refractory material labeled A60PT4 with a content of 65 wt.% Al2O3 and 36 wt.% SiO2. The properties of the andalusite material were a compressive strength of 106.9 MPa, an apparent porosity of 13%, and the recommended temperature of use up to 1300 °C. For corrosion testing, a static crucible test was performed according to the norm ČSN CEN/TS 15418 and the company’s internal regulation. The exposure time of the samples was 2 h and 5 h at temperatures of 1100 °C and 1400 °C for K2CO3 and ash, respectively. For the evaluation of tested samples, an X-ray powder differential analysis, an X-ray fluorescence analysis, scanning electron microscopy, and energy-dispersive X-ray spectroscopy were used.

19 February 2022 in Journal of Sustainable Metallurgy
Verified
Journal Article
Closed access
PDF file
PMPetra Matějková
Petra Matějková
Vlastimil MatějkaVlastimil Matějka
Vlastimil Matějka
TSTomáš Sabovčík
Tomáš Sabovčík
LGLuděk Gryžbon
Luděk Gryžbon
JVJozef Vlček
Jozef Vlček

10 December 2024 in Lubricants
Verified
Journal Article
Open access
PDF file
Vlastimil MatějkaVlastimil Matějka
Vlastimil Matějka
PJPriyadarshini Jayashree
Priyadarshini Jayashree
KFKryštof Foniok
Kryštof Foniok
JVJozef Vlcek
Jozef Vlcek
PMPetra Matějková
Petra Matějková
GSGiovanni Straffelini
Giovanni Straffelini
Magnetic fraction isolated from steel furnace slag was tested as a component of Cu-free friction composites. The friction–wear performance and production of wear particles during their testing using a pin-on-disc tester against a cast iron disc were evaluated. To compare the effect of the magnetic fraction on the parameters studied, the composite with alumina and the composite with original steel furnace slag were also prepared and tested. All composites showed a comparable friction coefficient. The composite with original steel furnace slag, and the composite with a magnetic fraction showed higher wear resistance compared to the composite containing alumina. The positive effect of the magnetic fraction on the extent of the emission of wear particles was observed and explained by the decreased aggressiveness of this composite to the cast iron disc. The influence of the phase composition of the steel furnace slag and the magnetic fraction on the friction film formation was also indicated, and its effect on the production of wear particles was proposed.

22 December 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
AVAlice Valigůrová
Alice Valigůrová
KČKristina Čabanová
Kristina Čabanová
PMPetra Matějková
Petra Matějková
JBJúlia Belobradová
Júlia Belobradová
JVJana Vaculova
Jana Vaculova
SHSilvie Heviánková
Silvie Heviánková
The paper focuses on describing a methodology for detecting microparticles in saliva and oral tissues using FTIR microscopy and scanning electron microscopy. The aim is to compare samples from patients with oral cavity carcinoma and healthy individuals, identify the presence of microparticles, and assess their potential association with carcinogenesis.