Selanna Roccella

Dr. Selanna Roccella


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 October 2020 in Journal of Fusion Energy
Verified
Journal Article
Open access
PDF file
SRSelanna Roccella
Selanna Roccella
GDG. Dose
G. Dose
RLR. de Luca
R. de Luca
MIM. Iafrati
M. Iafrati
AMA. Mancini
A. Mancini
GMG. Mazzitelli
G. Mazzitelli
Power exhaust is a key mission in the roadmap to the realization of a future fusion reactor. Among the different solutions, the use of liquid metals as plasma facing materials are of interest due to their potential increased lifetime. Several liquid metal limiters have been successfully tested in the Frascati Tokamak Upgrade over the last 10 years. Liquid materials such as lithium and tin have been investigated using capillary porous systems (CPSs), and their impact on plasma performance has been explored. From such experience, a liquid metal divertor (LMD) concept design, CPS-based, is here proposed. Tin has been preferred as plasma facing material. The proposed LMD would operate, in low evaporative regime, with matching heat exhausting capabilities to those of the baseline ITER-like divertor. Continuous refilling of the CPS is guaranteed with a reservoir at the back of the unit, where the metal is kept liquid through a gas heating circuit. The study has been carried out using ANSYS and the thermal results will be shown. All the design choices are compatible with the current materials and the constraints adopted for the DEMO W divertor. Using such configuration, thermal loads up to 20 MW/m2 are exhausted while keeping the surface temperature below 1250 °C. The design foresees values of pressure, temperature and flow rate of the water coolant in the same range expected for the W DEMO divertor, thus facilitating the integration of such solution in the current cassette design. Technological and practical aspects are addressed, i.e. tin corrosion and CPS wettability. Possible solutions to prevent tin corrosion, and its compatibility with structural materials, will be outlined.

11 October 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
GDGiacomo Dose
Giacomo Dose
SRSelanna Roccella
Selanna Roccella
FRFrancesco Romanelli
Francesco Romanelli
A substantial contribution of the stresses that arise inside the Plasma-Facing Components (PFCs) when a heat load is applied is caused by the mismatch of the Coefficient of Thermal Expansion (CTE) between the armor, usually made of tungsten (W), and the heat sink. A potential way to reduce such contribution to the secondary stresses is the use of an interlayer made with a Functionally Graded Material (FGM), to be interposed between the two sub-components. By tailoring the W concentration in the volume of the FGM, one can engineer the CTE in such a way that the thermal stresses are reduced inside the PFC. To minimize and, theoretically, reduce to zero the stresses due to the CTE mismatch, the FGM should ensure kinematic continuity between the armor and the heat sink, in a configuration where they deform into exactly the shape they would assume if they were detached from each other. We will show how this condition occurs when the mean thermal strain of each sub-component is the same. This work provides a methodology to determine the thickness and the spatial concentration function of the FGM able to ensure the necessary kinematic continuity between the two sub-components subjected to a generic temperature field monotonously varying in the thickness, while remaining stress-free itself. A method for the stratification of such ideal FGM is also presented. Additionally, it will be shown that the bending of the PFC, if allowed by the kinematic boundary conditions, does not permit, at least generally, the coupling of the expansion of the armor and of the heat sink. As an example of our methodology, a study case of the thermomechanical design of a steel-based PFC with an engineered W/steel FGM interlayer is presented. In such an exercise, we show that our procedure of engineering a FGM interlayer is able to reduce the linearized secondary stress of more than 24% in the most critical section of the heat sink, satisfying all the design criteria.

3 June 2024 in IEEE Transactions on Plasma Science
Verified
Journal Article
Open access
SRSelanna Roccella
Selanna Roccella
FGF. Giorgetti
F. Giorgetti
RLR. De Luca
R. De Luca
GSG. De Sano
G. De Sano
GDGiacomo Dose
Giacomo Dose
RNRudolf Neu
Rudolf Neu
The Divertor Tokamak Test (DTT) facility is a fusion device under construction in Italy. The mission of DTT is to test alternative divertor concepts under integrated physics and technological conditions that can reliably be extrapolated to DEMO. Due to the plasma core characteristics with relevant edge and scrape-off layer (SOL) parameters and a wall entirely in tungsten (W), DTT will provide an extensive set of information useful to select the most appropriate strategy for the power exhaust in DEMO. Several divertors, which may differ in design or/and technologies or/and poloidal profile, will be tested during the life of the machine. The first divertor to be installed will have to accommodate a multitude of strike points, located at various positions according to the different magnetic configurations, which will be tested in the first operational phases of the machine with the aim to identify the most promising. The first divertor will not test innovative technological solutions but will mainly take advantage of the technologies already qualified for the ITER divertor production. Thus, the entire divertor plasma-facing surface is designed to be used as targets: it will be made of W monoblocks joined on CuCrZr pipes (plasma-facing units, PFUs) similar to the ITER targets. With the purpose to increase the flexibility in operational scenarios by maximizing the allowable thermal load for the PFUs, the possibility of using monoblocks with a plasma side reduced thickness was investigated. By reducing the thickness of the armor, it is possible to limit plastic deformation of the monoblock and to preserve the characteristics of the plasma-facing surface during the component lifetime. A thickness between 3 and 4 mm is compatible both the erosion estimates in the DTT divertor area and the manufacturing constraints and therefore proposed for the DTT PFUs. Several mock-ups based on monoblock design were in the past tested under thermal fatigue, confirming the reliability of the monoblock design and the manufacturing processes, but with larger armor thicknesses (6–8 mm). The experimental verification of the monoblock performance with the proposed reduced thickness has been verified in the GLADIS facility at IPP Garching with a thermal load of 20 MW/m $^{2}$ applied for 1000 cycles of 10 s. The results showed the absence of plastic deformation and negligible increase in surface roughness.

11 April 2024 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
GSG. De Sano
G. De Sano
RLR. De Luca
R. De Luca
GDGiacomo Dose
Giacomo Dose
MPM. Furno Palumbo
M. Furno Palumbo
Michela GelfusaMichela Gelfusa
Michela Gelfusa
RNRudolf Neu
Rudolf Neu
The main mission of the divertor tokamak test (DTT) facility is to study advanced solutions for the power exhaust issue in view of a fusion power plant. In this respect, a significant amount of heat is expected to be absorbed by the first wall (FW) during operation. Therefore, the DTT FW is designed to be an actively water-cooled system. A proper hydraulic model is needed for the development of a cooling architecture of the system able to fulfill the requirements of operational safety under thermal loads and compliance with the DTT plant specifications. The present study aims to address this challenge, offering practical inputs for further optimization. Based on the existing conceptual design, the cooling circuits have been setup inside the plasma-facing components (PFCs). In this phase, empirical equations and hydraulic simulations have been adopted to investigate the hydraulic behavior of the modules that make up the FW and to evaluate the main design parameters, namely, velocity and pressure drops in the cooling channels. The outcome of such analysis demonstrated that the current design of the FW system complies with the imposed requirements. Moreover, operating flexibility has been demonstrated by identifying a proper range of the mass flow rate for each subsystem. Therefore, the models implemented in this study and the obtained findings prove to be suitable to support the next activities of engineering design of the FW.

4 April 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
CGClaudia Gasparrini
Claudia Gasparrini
DBD. Badocco
D. Badocco
LPLuigi Di Pace
Luigi Di Pace
NTNicholas Terranova
Nicholas Terranova
PPP. Pastore
P. Pastore
PSP. Sonato
P. Sonato
The Divertor Tokamak Test (DTT) vacuum vessel (VV) is a toroidal chamber that ensures an enclosed vacuum environment for the plasma, a confinement barrier, and temperature control. Water flows in the double-shell D-shaped VV cross-sectional structure made from stainless steel to operate at a set temperature. Beyond temperature control, the water cooling circuit needs to act as a neutron shielding media to protect the structures installed outside of the VV, namely, the superconducting coils. The shielding function is achieved due to the addition of boric acid in the water. The requirement on the borated water for the DTT VV is to have 8000-ppm B solution highly enriched in ¹⁰B (95% ¹⁰B). Given the lack of water chemistry guidelines for fusion power plants, the water chemistry requirements from fission power plants were investigated. In this work, general corrosion of stainless steel, 316L type family, in concentrated borated water solutions was investigated experimentally using metal release test. Samples were exposed to ultrapure water (UPW) and 8000-ppm B borated water at 80 °C for one week to quantify the amount of ions released in solution. 316L general corrosion was studied considering the different water chemistries, UPW versus borated water, and steels microstructures. DTT VV presents many welded joints, so general corrosion of welding-induced microstructure was here investigated compared to 316L base microstructure. The release of ions from general corrosion was found to be more influenced by water chemistry than microstructure.

17 April 2024 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
FGF. Giorgetti
F. Giorgetti
SRSelanna Roccella
Selanna Roccella
FCF. Crea
F. Crea
GDGiacomo Dose
Giacomo Dose
RLR. De Luca
R. De Luca
RNRudolf Neu
Rudolf Neu
The divertor tokamak test (DTT) facility is currently in the design stage and in the initial phase of construction at the research center ENEA Frascati. The DTT facility aims at searching integrated solutions for the power exhaust issue maintaining plasma performances compatible with future fusion devices. For this reason, the first DTT divertor was designed to accommodate different magnetic configurations: in particular other than single null (SN), the compatibility with X-divertor (XD) and negative triangularity (NT) with different leg lengths was ensured. To accommodate the strike point positions of the different magnetic equilibria, all plasma facing surfaces (i.e., inner and outer vertical targets, as well as the dome) have to be entirely made of tungsten (W) monoblocks. At the same time, to leave more space to the divertor legs, it was decided to design a dome with a flat shape. These two factors along with the armor with W monoblock and the flat shape have required finding ad hoc technological solutions for the plasma facing units (PFUs) of the dome with the need of a research and qualification phase. Above all, a W flat tiles (FTs) design was required at the inner dome end, where the copper cooling pipes turn by 90 $^{\circ}$ . The FT segment covers only a small length of the PFU ( $\sim$ 40 mm), and the goal is to join both monoblock and FT segments to the pipe in a single manufacturing process. The technique used is the hot radial pressing (HRP), which has been developed in ENEA and qualified for the manufacturing of the ITER inner vertical target.