Many researchers are interested in biofuels because it isenvironmentally friendly and potentially reduce global warming. Incorporating nanoparticles into biodiesel has increased its performance and emission characteristics. The current study examines the influence of magnesium oxide nanoadditions on the performance and emissions of a diesel engine that runs on C. vulgaris algae biodiesel. The transesterification process produced methyl ester from C. vulgaris algae biodiesel.The morphology of nanoadditives was studied using scanning electron microscopy, transmission electron microscopy, and energy‐dispersive X‐ray spectroscopy. The fuel sample consisted of biodiesel blends with and without magnesium oxide nanoadditives. The fuel properties of the prepared C. vulgaris methyl ester were found to conform with the ASTM standards. The experimental results were determined by running a single‐cylinder four‐stroke diesel engine at different load conditions. When compared to B20, a B20 blend containing 100 ppm magnesium oxide nanoparticles enhanced brake thermal efficiency while reducing specific fuel consumption, according to the research. When MgO nanoparticles were introduced to B20, engine emissions of HC, CO, and smoke were decreased.
In the construction of steel structures, the two most common types of structural members are hot-formed and cold-formed members. This paper mainly describes the analytical and experimental research on the strength and characteristics of CFS bolted built-up sigma sections having different structural arrangements under bending. The cross-sectional dimensions for the parametric study were selected by the sizes available in the market. In this paper, ANSYS workbench software was used to perform FE modeling and observe the local, flexural, and interaction of these buckling. Then, experimental study was performed by varying the arrangement of open section beams between face-to-face and back-to-back, connected using bolts or fasteners different spacings. Further, we conducted bending tests on cold-formed steel built-up members having simple edge stiffeners in the middle. Comparing both analytical and experimental studies, the results indicate that the back-to-back connected built-up beam section provides a flexural capacity higher than the face-to-face built-up section. Moreover, increasing the bolt spacing enhanced the load-carrying capacity of back-to-back sigma section built-up beams. It has also been discovered that the flexural strength of beams is primarily determined by bolt spacing or itsposition.
The research evaluates the impact of Sargassum algae methyl ester (SAME20) with 50 and 100 ppm silicon dioxide (SiO 2 ) nanoparticles on the performance and emissions of a single-cylinder, four-stroke diesel engine. SiO 2 nanoparticles were characterized using FTIR, SEM, and TEM. Diesel, SAME20, SAME20 + 50 ppm of SiO 2 , and SAME20 + 100 ppm of SiO 2 blends were tested at 1500 rpm under loads from 25% to 100%. The SAME20 + 100 ppm of SiO 2 blend outperformed others, improving brake thermal efficiency by 1.43% and reducing brake-specific fuel consumption by 5.35% compared to diesel. It also decreased HC, CO, and smoke emissions by 11.12%, 18.1%, and 16.2%, respectively, with a slight NO x increase. Tribological analysis using a four-ball tribometer showed the SAME20 + 100 ppm of SiO 2 blend reduced the coefficient of friction by 76.89% and wear scar diameter by 59.19%. SEM analysis confirmed reduced surface wear and damage, highlighting improved engine and tribological performance.
Nanoparticles are an emerging concept for increasing fuel properties. The purpose of this research work is to determine the effect of magnesium oxide nanoparticles on the performance and emission characteristics of diesel engines that run on a spirulina microalgae biodiesel blend (B20) as a fuel. The ultrasonication was used to disperse MgO nanoparticles in B20 fuel at various concentrations (25, 50, 75, and 100 ppm). The significant findings indicated that B20+100 blends reduced specific fuel consumption by 20.1% and had a 5.09% higher brake thermal efficiency than B20. B20+100 blends reduced CO, hydrocarbon, and smoke emissions by a maximum of 32.02%, 30.03%, and 26.07%, respectively, compared to B20.
1 July 2025 in Environmental Science and Pollution Research
The present study investigates the effects of magnesium oxide (MgO) nanoparticles on the performance and emissions of a single-cylinder diesel engine fueled by Datura stramonium L. methyl ester (DSLME) under constant speed and varying load conditions. SEM, TEM, and EDX spectroscopy were used to characterize the MgO nanoparticles. Experimental results showed that compared to DSLME20, the addition of 50 ppm MgO led to a 9.5% reduction in brake-specific fuel consumption and a 6.03% increase in brake thermal efficiency, highlighting the beneficial impact of MgO on thermal efficiency, aside from diesel fuel. Emissions analysis demonstrated significant reductions in carbon monoxide (CO), unburned hydrocarbons (HC), and smoke emissions. At full engine load, the DSLME20 + 50 ppm of MgO blend reduced CO by 7.9%, HC by 10.8%, and smoke by 8.7%, compared to DSLME20. However, nitrogen oxide (NOx) emissions increased by 6.3%. Additionally, tribological tests conducted using a four-ball tribometer at 1200 rpm, 75 °C, and a 40-kg load for 1 h revealed that the wear scar diameter for the DSLME20 + 50 ppm of MgO blend decreased by 15.74%, along with a 24.5% reduction in the coefficient of friction compared to the DSLME20. These findings suggest that MgO nanoparticles improve fuel efficiency, reduce emissions, and enhance engine durability and wear resistance in diesel engine applications.