In its main definition, piezoelectrets are polymeric structures with electric charged internal cavities. The bipolar-trapped charges form macro-dipoles that can be mechanically deformed, thus presenting a high piezoelectric coefficient in the order of hundreds of pC/N. Such results outperform most of the traditional piezoelectric polymers. As piezoelectrets can be manufactured by different methods, some of the techniques allow the inner cavities to be geometrically controlled, therefore providing some degree of freedom in the piezoelectric behavior. This report provides a description of the most relevant methods, starting with a brief introduction of piezoelectret origin and reaching recent achievements in piezoelectret production, such as additive manufacturing (3D printing). Materials that are frequently employed in piezoelectret fabrication and methods for improving their characteristics are also presented.

During petroleum industry operations, burning flammable gas components in the flaring stacks is common, normally a symbol for stable production, but flaring these components creates harmful emissions for the environment. This flaring gas has components with a high quantity of heating power, an important measurement that quantifies the energy that can potentially be obtained from this wasted resource. This paper aims to evaluate the energy usage of the flaring gas, estimating the possible energy produced with this usable resource by modeling a treatment and energy generation process employing the Aspen HYSYS^® simulator. The flaring gas is characterized using different models and compositional ranges of natural gas to know what kind of gas it is and identify what type of equipment could be used for treatment and energy generation from this resource. After the gas characterization, the selection of the equipment of treatment and energy generation is necessary; this is done using a multicriteria analysis by taking into consideration the variables of gas composition, electrical efficiency, economic performance, and GHG emissions, ensuring to generate the greatest amount of energy possible to be produced with this flaring gas. By increasing the LHV, 0.95 MMSCF of flared gas of an oilfield in the VMM basin produced 5133 kW, enough energy to supply gas treatment and power generation facilities and four times the total gross consumption energy of a model oilfield in the basin, while the CO₂ emissions were reduced 11.4%, and cost savings using this resource instead of diesel were obtained. In conclusion, to minimize flaring and to recover and reuse these waste components, looking for alternatives for the use of this gas-like power generation is an important option that reduces pollutants emission, gives a new source of fuel, and gives an energy usefulness to this wasted resource.

This work presents the development of a magnetic levitation system with a ferrite core, designed for electromagnetic energy harvesting from mechanical vibrations. The system consists of a fixed enamel-coated copper coil and five neodymium-iron-boron permanent magnets housed within a PVC spool. To enhance magnetic flux concentration, a manganese-zinc ferrite (Mn-Zn) ring was employed within the spool. Experimental tests were conducted at frequencies up to 20 Hz, demonstrating the device’s potential for harvesting energy from small vibrations, such as those generated by human biomechanical movements, achieving operating voltages up to 3 V. Additionally, the architecture is scalable for larger systems and allows for the integration of multiple transducers without magnetic field interference, independent of the frequency or excitation phase of each transducer.

This work presents the development and experimental validation of a low-cost, piezoelectret-based energy harvesting system integrated into a custom insole, as a promising alternative for future self-powered wearable electronics. The design utilizes eight thermoformed Teflon piezoelectrets, strategically positioned in high-impact regions (heel and forefoot), to convert footstep-induced mechanical motion into electrical energy. The sensors, fabricated using Fluorinated Ethylene Propylene (FEP) and Polytetrafluoroethylene (PTFE) layers via thermal pressing and aluminum sputtering, were connected in parallel to enhance signal consistency and robustness. A solenoid-actuated mechanical test rig was developed to simulate human gait under controlled conditions. The system consistently produced voltage pulses with peaks up to 13 V and durations exceeding ms, even under limited-force loading (10 kgf). Signal analysis confirmed repeatable waveform characteristics, and a Delon voltage multiplier enabled partial conversion into usable DC output. While not yet optimized for maximum efficiency, the proposed setup demonstrates the feasibility of using piezoelectrets for energy harvesting. Its simplicity, scalability, and low cost support its potential for future integration in applications such as fitness tracking, health monitoring, and GPS ultimately contributing to the development of autonomous, self-powered smart footwear systems. It is important to emphasize that the present study is a proof-of-concept validated exclusively under controlled laboratory conditions using a mechanical gait simulator. Future work will address real-time insole application tests with human participants.

This paper presents a low-cost/high-precision smart power supply for application on data loggers. The microprocessor unit is the brain of the system and manages the events and was optimized to provide electrical energy to the electronic devices under normal operation and under the presence of disruptive events. The measurements showed that when switching either from battery to AC or from AC to battery, neither caused the shutdown of the power supply nor affected the behavior of the power supply. The power supply was able to charge 80% of the battery on a fast recharge of 1 h and the remaining 20% on a slow recharge of 2 h. The current allocated to the battery did not affect the operation of the power supply. The tests also showed that the power supply was able to transmit relevant information about its operation to external computers through a serial connection. This information includes the voltages at the battery and at the output of the voltage regulators, the voltage level of the AC network, the level of the battery charge and if it was being recharged, the current being drained, the internal temperatures at two locations (one measured on the resistor that limits battery charge and another measured on the output diode of the regulators), and whether the cooling system is being used. The total cost of this smart power supply is less than $150, demonstrating good potential for its popularization.