In the study, experimental and theoretical studies were carried out to assess the influence of the shapes of dents in the tank wall on the stress-strain state of the defect zone. By testing fragments of a cylindrical tank, it was found that the most appropriate expression is (5), which could take into account the leaching of the tank wall, resulting in a decrease in the stress concentration index. At the same time, during theoretical studies in this paper, it was found that polynomials determined the stress concentration coefficient, where the obtained analytical expression data were compared with the data determined numerically in the ANSYS program, and it was found that the spread was from 2% to 10%. According to the results of a numerical study of the stress-strain state of the dent zone in the tank wall, graphical dependences of the stress concentration coefficient on the dimensionless depth of the dent for various values of the dimensionless radius of the dents and do not exceed 2% of the indicators that are obtained. At the conclusion of the experimental and numerical studies, a conclusion was made about the degree of influence of the geometric dimensions of the dents on the stress concentration index.

The paper presents the results of experimental studies of the features of the operation of prestressed shells, taking into account the various structural parameters of the prestress. It is established that when the winding angle changes from perpendicular to the shell axis to 75° and 65°, the circumferential stresses decrease 1.4 times and 1.2 times, respectively, and the axial stresses increase five and three times, which are two and four times lower than the circumferential, from which it can be concluded that the reduction in the winding angle to the longitudinal the axis of the shell has a positive effect on the stress state of the structure. The study also found that with an increase in the diameter of the winding wire from 1 to 2 mm and a change in the winding angle, the same nature of the stress distribution is observed, but the values of the stress state parameter change, so the efficiency increases up to 25% due to an increase in the winding thickness, depending on the pitch, angle and thickness of the winding, which favorably affects the strength and the bearing capacity of the structure as a whole by increasing the value of the stress state parameter. Thus, the results of the analysis will allow us to use in more detail the possibility of controlling the stress–strain state of the prestressed shell by changing the design parameters, and the results obtained can be used in design or construction, as well as when increasing the strength characteristics of the structure, which allows us to create a high-tech design optimal for these operating conditions, which can positively complement the studies conducted earlier in this direction.

This study provides a critical review and assessment of the problems of enhancing the research activity at a Kazakhstani pedagogical university that prepares future teachers. The aim of this study is to provide a rationale for the relevance of scientific and methodological support for increasing the research activity of teachers at pedagogical universities through the systematic integration of practitioner action research into professional practice. The value of action research is related to the change in and improvement of the professional practice of teachers based on the convergence of practice-oriented science and science-oriented practice. This work is in response to the gap in the professional preparation of future teachers, particularly in terms of developing research competencies and equipping future teachers with knowledge about action research. This is in marked contrast to in-service teachers who have been exposed to action research through the whole country’s ongoing reform of teacher education. Using a large survey of academic staff, the paper identifies the key factors influencing the research activity of university teachers. The findings from the survey and the narrative review suggest a willingness and openness to new ways of working among staff, which would make it possible to increase the research activity of university teachers themselves by integrating non-formal forms of research such as action research into their practice.

Precise meanings of thermophysical processes taking place in air gaps have decisive importance in composite cladding structure systems’ calculation and modeling. The climatic load conditions in Kazakhstan can significantly affect the microclimate of premises in general. In this work, a review study is carried out to obtain the relevant scientific literature on enclosing structures with air gaps under various climatic conditions. The review mainly covers research institutes from Sweden, Norway, France, Saudi Arabia, Russia, and China. On the issue of the air gap parameter’s influence on thermophysical processes, 16 papers were analyzed, and on the issue of air infiltration, 12 papers were analyzed. However, the review shows a lack of research in this area under various climatic conditions. At the same time, experience has shown that the principle of multilayer protection from climatic influences creates a favorable microclimate in buildings, but due to a possible temperature drop, wall structures made of composite building materials can be quite favorable under some conditions, and under others they may be less favorable. Therefore, working out a new energy-saving design with air gaps for climatic conditions with large temperature fluctuations during summer and winter is an urgent task.

Four series of experiments were carried out to study the possibility of replacing clay and an iron-containing component with tefritobasalt and lead slag as part of the initial charge for Portland cement. The experiments were carried out at atmospheric pressure and a temperature of 1350 °C. It was shown that the replacement of clay and an iron-containing component with tefritobasalt and lead slag as part of the initial charge in the cement industry will lead to a decrease in temperature by 100 °C in the technological scheme of production and a reduction in energy consumption, since the theoretical specific consumption of raw materials is 1.481 t/t of clinker, which is approximately 70 kg lower than in traditional mixtures. The content of non-traditional components in total was 24.69%. In addition, tefritobasalts improved clinker formation processes, contributed to a decrease in the firing temperature, and intensified the clinker firing process. A small amount of lead slag (5.06%) introduced into the mixture changed the structure of the clinker and improved the process of mineral formation while also improving roasting and reducing the anthropogenic impact on the environment through the disposal of man-made waste. The strength of the experimental composite cements was tested after 7 and 28 days on small samples measuring 2 × 2 × 2 cm. The physicomechanical characteristics and structure of composite cements were studied.