Daniel Frank

Mr. Daniel Frank

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
JSJonas Schröter
Jonas Schröter
TGTobias Graf
Tobias Graf
DFDaniel Frank
Daniel Frank
CBChristiane Bauer
Christiane Bauer
JKJosef Kallo
Josef Kallo
CWCaroline Willich
Caroline Willich

4 June 2023 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
DFDaniel Frank
Daniel Frank
JSJonas Schröter
Jonas Schröter
CBChristiane Bauer
Christiane Bauer
CWCaroline Willich
Caroline Willich

15 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
JSJonas Schröter
Jonas Schröter
DFDaniel Frank
Daniel Frank
VRValentin Radke
Valentin Radke
CBChristiane Bauer
Christiane Bauer
JKJosef Kallo
Josef Kallo
CWCaroline Willich
Caroline Willich
For the optimal high-efficiency operation of a PEM fuel cell system, the temperature, pressure, humidity and mass flow of the supplied air must be tuned to the fuel cell stack requirements. Especially for aircraft applications, this requires a thorough understanding of the fuel cell air supply system behavior and how it changes when the ambient pressure is below 1 bar(a) during flight. This work investigates the influence of low inlet pressures and varying inlet temperatures on the compression map of an electrical turbo charger. This is especially relevant in airborne fuel cell application and not much literature can be found on that topic. Compressor limits are evaluated experimentally and theoretically. The theory of mass flow and speed correction is compared to experimental findings and found to be applicable for the surge and speed limit of the investigated turbo chargers as long as the compressor map is not limited by the power of the electric motor and inverter. Based on this, a prediction of the compressor map for altitudes up to 10,000 m is made with the help of a developed software tool.

13 December 2024 in Energies
Verified
Journal Article
Open access
PDF file
CWCaroline Willich
Caroline Willich
DFDaniel Frank
Daniel Frank
TGTobias Graf
Tobias Graf
SWStefan Wazlawik
Stefan Wazlawik
SBSamara Brandao
Samara Brandao
CBChristiane Bauer
Christiane Bauer
A commercially available 100 kW PEM fuel cell system designed for efficient operation on ground-level was tested at low ambient pressures between 750 mbar and 940 mbar in a low-pressure chamber. The current–voltage characteristics at 940 mbar and 900 mbar showed only small differences, while the system performed worse at lower ambient pressures. To enable operation at these low pressures, an additional current-limiting strategy had to be implemented, as it was found that the compressor could not deliver sufficient mass flow at ambient pressures below 867 mbar to reach the maximum current allowed by the system (420 A). The results show that the fuel cell system, which was designed for ground-level applications, can be operated at lower pressures if the proposed current-limiting strategy is implemented, although at the cost of a lower maximum current output at low ambient pressures. Based on the results, suggestions for further hardware measures to optimise the system for flight conditions are made.

17 August 2022 in ACS Omega
Verified
Journal Article
Open access
DFDaniel Frank
Daniel Frank
GNGrace Neubauer
Grace Neubauer
CBChristiane Bauer
Christiane Bauer
JKJosef Kallo
Josef Kallo
CWCaroline Willich
Caroline Willich
To have more sustainable aviation, ways to reduce lead and gaseous emissions are important and currently large research topics. As further efficiency improvements for internal combustion engines (ICE) have reached a limit, and the research and development of certifiable full and hybrid electric aircrafts are still ongoing, it becomes increasingly important to investigate the use of alternatives to conventional fuels, such as bioethanol. In this study, a state-of-the-art turbocharged 104 kW flight piston engine (BRP Rotax 915 iS) was tested with fuels containing various amounts of ethanol to assess the influence on the engine's performance and emissions. Emission and performance maps covering the full range of engine operation from 4500 to 5800 RPM and about 40 to 110 kW output power were obtained using the standard fuel AvGas 100 LL, its current alternative Super 98 E5, and higher ethanol content fuels Super 98 E10 and Super 95 E20. With 20% ethanol in the fuel blend, a general decrease in CO and unburned hydrocarbon (UHC) emissions and an increase in CO2 and NOx were observed compared to the other fuels. Differences in the performance and emissions of the engine were also observed with different manifold air temperatures (MAT).

22 November 2024 in ECS Meeting Abstracts
Verified
Journal Article
Closed access
DFDaniel Frank
Daniel Frank
SWStefan Wazlawik
Stefan Wazlawik
SASamara Brandao de Almeida
Samara Brandao de Almeida
CBChristiane Bauer
Christiane Bauer
CWCaroline Willich
Caroline Willich
The performance of hydrogen PEM fuel cell systems can be optimized by means of pressurization of the cathode air, especially in aviation, where at in-flight conditions the pressure of the ambient air is significantly lower as at on-ground conditions. To provide the inlet air at optimal conditions (p, T, rH) during flight, an air supply system is required and in an all-electric aircraft the compression should happen by means of an electric centrifugal compressor. A challenge for the operation of a pressurised fuel cell system at high altitudes is the control of the compression system. Any unstable operation like compressor surge has to be avoided, since it can damage both the fuel cell stack and the compressor itself. For the development of such an air supply system, a combined experimental and modeling approach was chosen. A hydrogen PEM fuel cell system was characterized at nominal and at low cathode pressures to obtain the behavior at flight relevant conditions and an experimental air supply system containing electric compressor, intercooler, humidifier, cathode volume and throttle valve at the outlet has been set up and used for the development, parameterization, and validation of a model for the compression system. The model is based on the Greitzer model 1,2, and has been extended to also represent the additional components between the compressor and the throttle valve (intercooler, humidifier, and cathode volume) 3. It is now able to predict the transient response of the entire air supply system to changes in the reference values of compressor speed and valve opening angle and the resulting mass flow changes and pressures within the individual components. The model and the data from the fuel cell system were used for the development of improved control strategies, that make it possible to operate the system safely in a wide range of operating conditions. Unstable situations, like compressor surge, are avoided by these control strategies even in the highly varying conditions during a flight. The developed control strategies are verified on the hardware of the experimental setup and tested under realistic flight conditions in a low-pressure climate chamber. References Greitzer, E. M. Surge and Rotating Stall in Axial Flow Compressors—Part I: Theoretical Compression System Model. Journal of Engineering for Power 98, 190–198 (1976). Gravdahl, J. T. & Egeland, O. Compressor Surge and Rotating Stall. (Springer London, London, 1999). doi:10.1007/978-1-4471-0827-6. Frank, D., Bauer, C. & Willich, C. Modeling of the cathode air supply for a pressurized hydrogen fuel cell system in airborne applications. Proceedings of the Aerospace Europe Conference 2023 (2023) doi:10.13009/EUCASS2023-218.