Ge alloying in kesterite thin films enables to mitigate electronic defect and disorder, enhance morphology as well as realize bandgap grading, all contributing to higher performance of complete solar cells via resolved Voc and fill factor deficits.
Kesterite photovoltaic technologies are critical for the deployment of light‐harvesting devices in buildings and products, enabling energy sustainable buildings, and households. The recent improvements in kesterite power conversion efficiencies have focused on improving solution‐based precursors by improving the material phase purity, grain quality, and grain boundaries with many extrinsic doping and alloying agents (Ag, Cd, Ge…). The reported progress for solution‐based precursors has been achieved due to a grain growth in more electronically intrinsic conditions. However, the kesterite device performance is dependent on the majority carrier density and sub‐optimal carrier concentrations of 10 14 –10 15 cm −3 have been consistently reported. Increasing the majority carrier density by one order of magnitude would increase the efficiency ceiling of kesterite solar cells, making the 20% target much more realistic. In this work, LiClO 4 is introduced as a highly soluble and highly thermally stable Li precursor salt which leads to optimal (>10 16 cm −3 ) carrier concentration without a significant impact in other relevant optoelectronic properties. The findings presented in this work demonstrate that the interplay between Li‐doping and Ag‐alloying enables a reproducible and statistically significant improvement in the device performance leading to efficiencies up to 14.1%.
3 March 2025 in Progress in Photovoltaics: Research and Applications
The present research explores for the first time the intricate relationship between sulfurization temperature at unusual high temperatures (up to 700°C) and the structural/optoelectronic properties of Cu2(Zn,Cd)SnS4 (CZCTS) thin films, synthesized via a two‐step sequential process involving the precursor film deposition using aprotic molecular ink followed by thermal treatment in sulfur atmosphere. X‐ray diffraction patterns confirms the tetragonal structure. Scanning Electron Micrographs revealed significant grain growth, with grain sizes increasing from ~0.3 μm at 620°C to ~1.5 μm at 680°C, effectively reducing grain boundary recombination. Energy dispersive X‐ray spectroscopy demonstrated a Cu‐poor and Zn‐rich composition, with a consistent Cd incorporation of ~3.7 at%. Raman spectroscopy showcases the homogeneity and purity of the CZCTS crystalline structure. Precise control of the sulfurization temperature plays a crucial role in determining the photovoltaic characteristics of CZCTS‐based solar cells. By increasing the grain size and preventing the thermal decomposition of the CZTS phase, the photovoltaic performance peaked at a sulfurization temperature of 680°C, achieving a power conversion efficiency (PCE) of 10.4%, with an open‐circuit voltage of 0.701 V, a short‐circuit current density of 24.3 mA/cm2 and a fill factor of 60.8%. External quantum efficiency reached a maximum of 83.3% at 580 nm. The bandgap of the CZCTS absorber was determined to be 1.48 eV, optimal for photovoltaic applications. However, further increasing the sulfurization temperature to 700°C resulted in a lower PCE of 8.5%, attributed to interface degradation and secondary phase formation. Temperature‐dependent current–voltage measurements revealed a reduction in recombination losses, with an activation energy of 1.24 eV at the CZCTS/CdS interface, indicating effective defect passivation by Cd incorporation. The optimized films, sulfurized at 680°C, displayed an absorber thickness of ~1.2 μm after sulfurization, providing efficient light absorption and charge transport. The findings not only emphasize the critical role of sulfurization temperature in engineering CZCTS film and subsequently their functionality but also provide valuable insights for fine tuning their performance in the field of photovoltaic applications.
The sustainable and harmless Cu2ZnSn(S,Se)4 kesterite materials for thin-film photovoltaics are still lacking efficiency, which may be solved by bandgap grading, herein obtained by two-step annealing in H2Se gas of metallic precursors.