Agricultural mechanization is crucial in enhancing production efficiency, alleviating labor demands, reducing costs, improving agricultural product quality, and promoting sustainable development. However, wear and tear are inevitable when using agricultural machinery. The failure of critical wear-resistant parts is responsible for over 50% of rural machinery breakdowns. For instance, a domestic combine harvester typically only operates trouble-free for 20 to 30 h, and the service life of a rotary plow knife is approximately 80 h. Investigating the wear performance of key farm machinery components reinforces machinery design and maintenance strategies, extends machinery lifespans, enhances agricultural production efficiency, and advances agrarian sustainability. This paper provides a comprehensive overview of the latest research on the wear resistance of crucial agricultural machinery components. It delves into the factors influencing the wear resistance of these components and explores current effective measures to address wear-related issues. Additionally, it also summarizes the challenges and opportunities in researching the wear performance of key components in agricultural machinery and future development directions.

The effect and mechanism of grain sizes on the tribological behavior of CoCrFeMnNi high entropy alloy (HEA) were studied by friction experiments and wear morphology analysis. Under normal low load and low sliding speed, the primary wear mechanism of the HEA samples is adhesive wear. With the increase in sliding speed, the wear mechanisms of the samples are adhesive wear and oxidation wear. The oxide layer formed under the action of friction heat of the coarse grain (CG) sample is easy to break due to the softening of the CG. With the increase of normal load and sliding speed, the wear mechanisms of the HEA samples are mainly adhesive wear, oxidation wear, and plastic deformation. The oxide layer of CG sample has many cracks, and the worn surface also has plastic deformation, which leads to the increase of friction coefficient and specific wear rate and the decrease of wear resistance. Therefore, the fine grain size HEA sample has better wear resistance than the CG sample due to its high surface strength.

The hardness of passion fruit is a critical feature to consider when determining maturity during post-harvest storage. The capacity of near-infrared diffuse reflectance spectroscopy (NIRS) for non-destructive detection of outer and inner hardness of passion fruit epicarp was investigated in this work. The passion fruits’ spectra were obtained using a near-infrared spectrometer with a wavelength range of 10,000–4000 cm⁻¹. The hardness of passion fruit’s outer epicarp (F1) and inner epicarp (F2) was then measured using a texture analyzer. Moving average (MA) and mean-centering (MC) techniques were used to preprocess the collected spectral data. Competitive adaptive reweighted sampling (CARS), successive projection algorithm (SPA), and uninformative variable elimination (UVE) were used to pick feature wavelengths. Grid-search-optimized random forest (Grids-RF) models and genetic-algorithm-optimized support vector regression (GA-SVR) models were created as part of the modeling process. After MC preprocessing and CARS selection, MC-CARS-Grids-RF model with 7 feature wavelengths had the greatest prediction ability for F1. The mean square error of prediction set (RMSE_P) was 0.166 gN. Similarly, following MA preprocessing, the MA-Grids-RF model displayed the greatest predictive performance for F2, with an RMSE_P of 0.101 gN. When compared to models produced using the original spectra, the R²_P for models formed after preprocessing and wavelength selection improved. The findings showed that near-infrared spectroscopy may predict the hardness of passion fruit epicarp, which can be used to identify quality during post-harvest storage.

The effects of different Cr contents on the corrosion resistance of FeCoNiMnCr_x (x = 0.5;1;1.5) porous high-entropy alloys (HEAs) in 3.5 wt.% NaCl solution on corrosion resistance was investigated. With the increase in Cr content, the total porosity and permeability of the porous HEA increased. The increase in porosity improves the interconnectivity between the pores and enhances the contact area with the corrosion solution. The pore-making mechanism is mainly a powder compaction, and Kirkendall holes are caused by different elements due to different diffusion rates. With the increase in Cr content, the i_corr increases, and the E_corr decreases in the porous HEAs of FeCoNiMnCr_x (x = 0.5;1;1.5). The corrosion resistance of FeCoNiMnCr_x (x = 0.5;1;1.5) porous HEAs decreases with the increase in the Cr element. With the increase in Cr content, the weight gain rate of FeCoNiMnCr_x porous HEA increases gradually after immersion for 168 h, and the average pore size and permeability of the sample decrease gradually. The corrosion resistance of FeCoNiMnCr_x porous HEA decreases with increasing Cr content.

Titanium carbide (TiC) coatings were prepared on the surface of AlFeCoCrNiCu high-entropy alloy blocks using electro-spark deposition (ESD). The microhardness and corrosion resistance of the TiC coatings prepared under different voltage and capacitance process parameters were studied. The research shows that the maximum microhardness of the TiC coating on sample 4 (working voltage of 20 V, working capacitance of 1000 μF) is 844.98 HV, which is 81.5% higher than the microhardness of the substrate. This is because the deposition energy increases with the increase in voltage, and the adhesion and aggregation between the coating and the substrate are enhanced, increasing the hardness of the coating. It is worth noting that excessive deposition energy can increase surface defects and reduce the microhardness of the coating surface. Electrochemical testing analysis shows that the corrosion current density of the TiC coating is the lowest (9.475 × 10⁻⁷ ± 0.06 × 10⁻⁷), and the coating impedance is the highest (2.502 × 10³ Ω·com²). The absolute phase angle value is the highest (about 72°). The above indicates that the TiC coating prepared with a working voltage of 20 V and a working capacitance of 1000 μF has better microhardness and corrosion resistance.

In this study, the corrosion behavior of Cu_XCoCrMoNi (x = 0.3, 0.6, 0.9) high-entropy alloys (HEAs) in 3.5% NaCl solution is systematically investigated. The alloy samples show a strong link between copper content and corrosion resistance. It is noteworthy that an increase in copper content promotes element segregation, resulting in an increase in corrosion current density from 2.138 × 10⁻⁷ μA/cm² to 1.8989 × 10⁻⁶ μA/cm² and a decrease in charge transfer resistance from 182.6 Ω·cm² to 42.34 Ω·cm². In addition, electrochemical experiments demonstrate that lowering the copper content in the alloys reduces the spread and depth of corrosion. All alloys exhibit n-type semiconductor behavior, with donor density increasing from 4.792 × 10²³ cm⁻³ to 5.581 × 10²³ cm⁻³ with increasing copper content. Notably, the passive film is characterized by the presence of Cr₂O₃ and Cu₂O as its main constituents. As the copper content in the HEA increases, higher levels of copper oxides in the passive film inhibit the formation of chromium oxides. This degrades the passive film quality, thereby diminishing the overall corrosion resistance.