In this study, the combination of hydrothermal technique and seed-doping method was conducted to coordinately control the formation of fine MgO-Y2O3 powders, which are promising mid-infrared materials applied to hypersonic aircraft windows due to their excellent infrared transmissions over wide regions. Y(NO3)3·6H2O, Mg(NO3)2·6H2O, Y2O3 seeds and MgO seeds were used as raw materials to prepare the MgO-Y2O3 composite powders (50:50 vol.%), and the influences of the seed contents and hydrothermal treatment temperatures on the final powders and hot-pressed ceramics were investigated by XRD, SEM and TEM techniques. The results show that powders with a seed content of 5% that are hydrothermally synthesized at 190 °C can present a better uniformity and dispersion with a particle size of ~125 nm. Furthermore, the ceramics prepared with the above powders displayed a homogenous two-phase microstructure, fewer pores and a fine grain size with Y2O3 of ~1 µm and MgO of ~620 nm. The present study may open an avenue for developing transparent ceramics based on MgO-Y2O3 nanopowders prepared by hydrothermal technique.
W is a widely used refractory metal with ultra-high melting point up to 3410 °C. However, its applications are limited by poor ablation resistance under high-temperature flame and air flow, which is crucial for aerospace vehicles. To improve the ablation resistance of W under extreme conditions, W-Y alloys doped with different Hf mass fractions (0, 10, 20, and 30) were prepared using the fast hot pressing sintering method. Microstructure and ablation behaviours at 2000 °C were investigated. Results showed that adding an appropriate amount of Hf improved the properties of the W-Y alloy evidently. In particular, the hardness of the alloy increased with the increased content of Hf. The formation of the HfO2 layer on the surface during ablation decreased the mass and linear ablation rates, indicating enhanced ablation resistance. However, excessive Hf addition will result in crack behaviour during ablation. With a Hf content of 20 wt.%, the alloy exhibited high stability and an excellent ablation resistance.
Abradable seal coatings represent a critical technology within the realm of advanced power systems, designed to minimize airflow channel leakage, thereby reducing energy consumption and enhancing overall efficiency. In the present study, CuAl/BN, CuAlLaF3/BN, and CuAlY/BN abradable seal coatings were prepared using plasma spraying technology. Both the as-deposited coatings and high-temperature oxidation-treated coatings were comprehensively investigated by means of scanning electron microscopy (SEM), open-circuit potentials (OCP), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), salt-spray corrosion testing, and bond strength evaluations. The results show that the addition of rare earth elements to the CuAl/BN coatings does not enhance the corrosion resistance of the coatings and even leads to a decrease in the corrosion resistance of the coatings. In contrast, the CuAlY/BN coatings exhibited a significant improvement in corrosion resistance following an oxidation treatment at 550 °C. This enhancement is attributed to the yttrium (Y) element, which facilitates the formation of passivation films and confers a resistance effect, thereby bolstering the coatings’ resistance to corrosion. The bond strength of the high-temperature oxidation-treated CuAlY/BN coating was improved by about 30% after 960 h of salt-spray corrosion.
Hysteresis related to first-order phase transformation in shape memory alloys, which is the macroscopic manifestation of energy dissipation, is detrimental to the precise control of actuation and causes structural and functional fatigue of components. It is of vital importance to explore high-performance shape memory alloys with low stress-hysteresis, large superelasticity, and wide temperature range operation in practical applications. Here, we have developed a Ni-Mn-Fe-In shape memory microwire, exhibiting an ultra-low stress-hysteresis and huge tensile superelasticity in a wide temperature range. The microwire shows a smooth surface and a single crystal structure (with ⟨001⟩A-oriented along the axial direction of microwire), and the microstructure of the microwire contains austenite matrix and sparsely distributed precipitates with an average size of 20–80 nm, all of which may be beneficial to obtain low hysteresis and large strains in the microwire. As a result, the microwire exhibits a minimum stress-hysteresis of as low as 8.5 MPa (with overall strain of 15.3%) and corresponding energy dissipation as low as 1.44 MJ/m3. The microwire always shows a low stress-hysteresis (less than 24 MPa) and low energy dissipation (less than 2.86 MJ/m3) above room temperature. The microwire shows a huge superelasticity with recoverable strains higher than 15% in the wide temperature range from 218 to 418 K. Together with the advantages of easy fabrication and no post-processing required, this microwire shows a tremendous potential for cyclic actuators and energy conversion devices under multi-field coupling.
HfO2 has become a promising thermal barrier coating material due to its similarity in structure and chemical properties with ZrO2 and its higher phase structure transition temperature. However, the fracture toughness of HfO2 is not ideal, greatly limiting its application. In this report, we find a special sandwich structure of ceramics, comprising a cubic (C) phase /monoclinic (M) phase/cubic (C) phase. The microstructural evolution and mechanical properties of these ceramics were investigated under annealing at 1500 °C. The results indicate that, with an increase in annealing duration, there was a gradual augmentation in the proportion of the monoclinic (M) phase and the fracture toughness increased from 2.18 MPa·m0.5 to 2.83 MPa·m0.5 after 48 h of annealing, which is higher than many potential TBC materials. The residual compressive stress present in the M phases during the progression of crack propagation served to facilitate the bridging and deflection of cracks. As such, this process led to the alleviation of stress concentration at the crack tip, ultimately enhancing the toughening effect.
Significant interest in the stoichiometric and off-stoichiometric Fe2MnGa alloys is based on their complex phase transition behavior and potential application. In this study, temperature- and magnetic-field-induced phase transformations in the Fe41.5Mn28Ga30.5 magnetic shape memory alloy were investigated by in situ synchrotron high-energy X-ray diffraction and in situ neutron diffraction techniques. It was found that incomplete phase transformation and phase coexistence behavior are always observed while applying and removing fields in Fe41.5Mn28Ga30.5. Typically, even at 4 K and under 0 T, or increasing the magnetic field to 11 T at 250 K, it can be directly detected that the martensite and austenite are in competition, making the phase transition incomplete. TEM observations at 300 K and 150 K indicate that the anti-phase boundaries and B2 precipitates may lead to field-induced incomplete phase transformation behavior collectively. The present study may enrich the understanding of field-induced martensitic transformation in the Fe-Mn-Ga magnetic shape memory alloys.