Hao Lan

Hao Lan


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
YLYunpeng Li
Yunpeng Li
HSHongqian Sun
Hongqian Sun
JSJing Song
Jing Song
ZZZhiyu Zhang
Zhiyu Zhang
Hao LanHao Lan
Hao Lan
KXKeqiang Xie
Keqiang Xie
Yttria-stabilized zirconia (YSZ) has been widely used in structural and functional ceramics because of its excellent physicochemical properties. In this paper, the density, average gain size, phase structure, and mechanical and electrical properties of conventionally sintered (CS) and two-step sintered (TSS) 5YSZ and 8YSZ are investigated in detail. As the grain size of YSZ ceramics became smaller, dense YSZ materials with a submicron grain size and low sintering temperature were optimized in terms of their mechanical and electrical properties. 5YSZ and 8YSZ in the TSS process significantly improved the plasticity, toughness, and electrical conductivity of the samples and significantly suppressed the rapid grain growth. The experimental results showed that the hardness of the samples was mainly affected by the volume density, that the maximum fracture toughness of 5YSZ increased from 3.514 MPa·m1/2 to 4.034 MPa·m1/2 in the TSS process, an increase of 14.8%, and that the maximum fracture toughness of 8YSZ increased from 1.491 MPa·m1/2 to 2.126 MPa·m1/2, an increase of 42.58%. The maximum total conductivity of the 5YSZ and 8YSZ samples under 680 °C increased from 3.52 × 10−3 S/cm and 6.09 × 10−3 S/cm to 4.52 × 10−3 S/cm and 7.87 × 10−3 S/cm, an increase of 28.41% and 29.22%, respectively.

23 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
SYShangyu Yang
Shangyu Yang
Hao LanHao Lan
Hao Lan
Xiaoming SunXiaoming Sun
Xiaoming Sun
SFShaowei Feng
Shaowei Feng
WZWeigang Zhang
Weigang Zhang
In this study, the combination of hydrothermal technique and seed-doping method was conducted to coordinately control the formation of fine MgO-Y2O3 powders, which are promising mid-infrared materials applied to hypersonic aircraft windows due to their excellent infrared transmissions over wide regions. Y(NO3)3·6H2O, Mg(NO3)2·6H2O, Y2O3 seeds and MgO seeds were used as raw materials to prepare the MgO-Y2O3 composite powders (50:50 vol.%), and the influences of the seed contents and hydrothermal treatment temperatures on the final powders and hot-pressed ceramics were investigated by XRD, SEM and TEM techniques. The results show that powders with a seed content of 5% that are hydrothermally synthesized at 190 °C can present a better uniformity and dispersion with a particle size of ~125 nm. Furthermore, the ceramics prepared with the above powders displayed a homogenous two-phase microstructure, fewer pores and a fine grain size with Y2O3 of ~1 µm and MgO of ~620 nm. The present study may open an avenue for developing transparent ceramics based on MgO-Y2O3 nanopowders prepared by hydrothermal technique.

22 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
RWRui Wu
Rui Wu
CHChuanbing Huang
Chuanbing Huang
ZHZhang Huifeng
Zhang Huifeng
HLHaozhong Lv
Haozhong Lv
Xiaoming SunXiaoming Sun
Xiaoming Sun
WZWeigang Zhang
Weigang Zhang
W is a widely used refractory metal with ultra-high melting point up to 3410 °C. However, its applications are limited by poor ablation resistance under high-temperature flame and air flow, which is crucial for aerospace vehicles. To improve the ablation resistance of W under extreme conditions, W-Y alloys doped with different Hf mass fractions (0, 10, 20, and 30) were prepared using the fast hot pressing sintering method. Microstructure and ablation behaviours at 2000 °C were investigated. Results showed that adding an appropriate amount of Hf improved the properties of the W-Y alloy evidently. In particular, the hardness of the alloy increased with the increased content of Hf. The formation of the HfO2 layer on the surface during ablation decreased the mass and linear ablation rates, indicating enhanced ablation resistance. However, excessive Hf addition will result in crack behaviour during ablation. With a Hf content of 20 wt.%, the alloy exhibited high stability and an excellent ablation resistance.

12 September 2024 in Crystals
Verified
Journal Article
Open access
PDF file
YLYongjun Liu
Yongjun Liu
CHChuanbing Huang
Chuanbing Huang
HYHao Yang
Hao Yang
Xiaoming SunXiaoming Sun
Xiaoming Sun
ZHZhang Huifeng
Zhang Huifeng
SYShouquan Yu
Shouquan Yu
Abradable seal coatings represent a critical technology within the realm of advanced power systems, designed to minimize airflow channel leakage, thereby reducing energy consumption and enhancing overall efficiency. In the present study, CuAl/BN, CuAlLaF3/BN, and CuAlY/BN abradable seal coatings were prepared using plasma spraying technology. Both the as-deposited coatings and high-temperature oxidation-treated coatings were comprehensively investigated by means of scanning electron microscopy (SEM), open-circuit potentials (OCP), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), salt-spray corrosion testing, and bond strength evaluations. The results show that the addition of rare earth elements to the CuAl/BN coatings does not enhance the corrosion resistance of the coatings and even leads to a decrease in the corrosion resistance of the coatings. In contrast, the CuAlY/BN coatings exhibited a significant improvement in corrosion resistance following an oxidation treatment at 550 °C. This enhancement is attributed to the yttrium (Y) element, which facilitates the formation of passivation films and confers a resistance effect, thereby bolstering the coatings’ resistance to corrosion. The bond strength of the high-temperature oxidation-treated CuAlY/BN coating was improved by about 30% after 960 h of salt-spray corrosion.

15 March 2024 in Crystals
Verified
Journal Article
Open access
PDF file
YWyang Wu
yang Wu
Hao LanHao Lan
Hao Lan
Xiaoming SunXiaoming Sun
Xiaoming Sun
ZHZIHAO HU
ZIHAO HU
YSYonghui Sun
Yonghui Sun
WZWeigang Zhang
Weigang Zhang
HfO2 has become a promising thermal barrier coating material due to its similarity in structure and chemical properties with ZrO2 and its higher phase structure transition temperature. However, the fracture toughness of HfO2 is not ideal, greatly limiting its application. In this report, we find a special sandwich structure of ceramics, comprising a cubic (C) phase /monoclinic (M) phase/cubic (C) phase. The microstructural evolution and mechanical properties of these ceramics were investigated under annealing at 1500 °C. The results indicate that, with an increase in annealing duration, there was a gradual augmentation in the proportion of the monoclinic (M) phase and the fracture toughness increased from 2.18 MPa·m0.5 to 2.83 MPa·m0.5 after 48 h of annealing, which is higher than many potential TBC materials. The residual compressive stress present in the M phases during the progression of crack propagation served to facilitate the bridging and deflection of cracks. As such, this process led to the alleviation of stress concentration at the crack tip, ultimately enhancing the toughening effect.

12 April 2024 in Crystals
Verified
Journal Article
Open access
PDF file
HYHao Yang
Hao Yang
CHChuanbing Huang
Chuanbing Huang
HLHaozhong Lv
Haozhong Lv
YLYongjun Liu
Yongjun Liu
YSYonghui Sun
Yonghui Sun
WZWeigang Zhang
Weigang Zhang
This article details a method for preparing cermet matrix composites via Fast hot pressing (FHP) sintering technology and emphasizes their potential use in extremely high-temperature settings. The material primarily consists of NiCr alloy, Cr3C2, and LaF3. An in-depth investigation was conducted on the tribological properties of the specimen by conducting sliding tests against a Si3N4 ball at varying temperatures, including room temperature (RT), 400 °C, 600 °C, and 800 °C. Advanced techniques such as scanning electron microscopy, micro-XRD, and micro-Raman spectroscopy were employed to examine the friction surfaces formed under different frictional temperatures. The findings reveal a uniform composition and high density within the composites. It is noteworthy that as the LaF3 content increases, the hardness of the ceramic phase diminishes. Conversely, the hardness of the alloy phase augments with the addition of LaF3, provided that its content remains below 15 wt%. The composite material containing 15 wt% LaF3 demonstrates superior hardness values, with the ceramic phase reaching HV1412 and the alloy phase achieving HV384. Furthermore, the coefficient of friction of the composite material was evaluated. The coefficient of friction of the composite is between 0.74 and 0.4 and the wear rate is 4.46 × 10−6–5.72 × 10−5 mm3N−1m−1 from room temperature to 800 °C. The lubrication behavior at low temperature is mainly attributed to the lubricating effect of LaF3, and at high temperature it is due to the tribochemical reaction to form LaCrO3 with good lubricating properties, which plays a synergistic lubricating role with Cr2O3.