Zhang Huifeng

Dr. Zhang Huifeng


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 November 2021 in Crystals
Verified
Journal Article
Open access
PDF file
QSQian Sun
Qian Sun
ZHZhang Huifeng
Zhang Huifeng
CHChuanbing Huang
Chuanbing Huang
WZWeigang Zhang
Weigang Zhang
In this paper, we aimed to improve the oxidation and ablation resistance of carbon fiber-reinforced carbon (CFC) composites at temperatures above 2000 °C. C/C–SiC–ZrB2 ultra-high temperature ceramic composites were fabricated through a complicated liquid–solid reactive process combining slurry infiltration (SI) and reactive melt infiltration (RMI). A liquid Si–Zr10 eutectic alloy was introduced, at 1600 °C, into porous CFC composites containing two kinds of boride particles (B4C and ZrB2, respectively) to form a SiC–ZrB2 matrix. The effects and mechanism of the introduced B4C and ZrB2 particles on the formation reaction and microstructure of the final C/C–SiC–ZrB2 composites were investigated in detail. It was found that the composite obtained from a C/C–B4C preform displayed a porous and loose structure, and the formed SiC–ZrB2 matrix distributed heterogeneously in the composite due to the asynchronous generation of the SiC and ZrB2 ceramics. However, the C/C–SiC–ZrB2 composite, prepared from a C/C–ZrB2 preform, showed a very dense matrix between the fiber bundles, and elongated plate-like ZrB2 ceramics appeared in the matrix, which were derived from the dissolution–diffusion–precipitation mechanism of the ZrB2 clusters. The latter composite exhibited a relatively higher ZrB2 content (9.51%) and bulk density (2.82 g/cm3), along with lower open porosity (3.43%), which endowed this novel composite with good mechanical properties, including pseudo-plastic fracture behavior.

22 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
RWRui Wu
Rui Wu
CHChuanbing Huang
Chuanbing Huang
ZHZhang Huifeng
Zhang Huifeng
HLHaozhong Lv
Haozhong Lv
Xiaoming SunXiaoming Sun
Xiaoming Sun
WZWeigang Zhang
Weigang Zhang
W is a widely used refractory metal with ultra-high melting point up to 3410 °C. However, its applications are limited by poor ablation resistance under high-temperature flame and air flow, which is crucial for aerospace vehicles. To improve the ablation resistance of W under extreme conditions, W-Y alloys doped with different Hf mass fractions (0, 10, 20, and 30) were prepared using the fast hot pressing sintering method. Microstructure and ablation behaviours at 2000 °C were investigated. Results showed that adding an appropriate amount of Hf improved the properties of the W-Y alloy evidently. In particular, the hardness of the alloy increased with the increased content of Hf. The formation of the HfO2 layer on the surface during ablation decreased the mass and linear ablation rates, indicating enhanced ablation resistance. However, excessive Hf addition will result in crack behaviour during ablation. With a Hf content of 20 wt.%, the alloy exhibited high stability and an excellent ablation resistance.

18 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
YLYang Li
Yang Li
MGMin Ge
Min Ge
SYShouquan Yu
Shouquan Yu
ZHZhang Huifeng
Zhang Huifeng
CHChuanbing Huang
Chuanbing Huang
WZWeigang Zhang
Weigang Zhang
Boron nitride (BN) ceramic fibers containing amounts of silicon nitride (Si3N4) were prepared using hybrid precursors of poly(tri(methylamino)borazine) (PBN) and polycarbosilane (PCS) via melt-spinning, curing, decarburization under NH3 to 1000 °C and pyrolysis up to 1600 °C under N2. The effect of Si3N4 contents on the microstructure of the BN/Si3N4 composite ceramics was investigated. Series of the BN/Si3N4 composite fibers containing various amounts of Si3N4 from 5 wt% to 25 wt% were fabricated. It was found that the crystallization of Si3N4 could be totally restrained when its content was below 25 wt% in the BN/Si3N4 composite ceramics at 1600 °C, and the amorphous BN/Si3N4 composite ceramic could be obtained with a certain ratio. The mean tensile strength and Young’s modulus of the composite fibers correlated positively with the Si3N4 mass content, while an obvious BN (shell)/Si3N4 (core) was formed only when the Si3N4 content reached 25 wt%.

12 September 2024 in Crystals
Verified
Journal Article
Open access
PDF file
YLYongjun Liu
Yongjun Liu
CHChuanbing Huang
Chuanbing Huang
HYHao Yang
Hao Yang
Xiaoming SunXiaoming Sun
Xiaoming Sun
ZHZhang Huifeng
Zhang Huifeng
SYShouquan Yu
Shouquan Yu
Abradable seal coatings represent a critical technology within the realm of advanced power systems, designed to minimize airflow channel leakage, thereby reducing energy consumption and enhancing overall efficiency. In the present study, CuAl/BN, CuAlLaF3/BN, and CuAlY/BN abradable seal coatings were prepared using plasma spraying technology. Both the as-deposited coatings and high-temperature oxidation-treated coatings were comprehensively investigated by means of scanning electron microscopy (SEM), open-circuit potentials (OCP), potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), salt-spray corrosion testing, and bond strength evaluations. The results show that the addition of rare earth elements to the CuAl/BN coatings does not enhance the corrosion resistance of the coatings and even leads to a decrease in the corrosion resistance of the coatings. In contrast, the CuAlY/BN coatings exhibited a significant improvement in corrosion resistance following an oxidation treatment at 550 °C. This enhancement is attributed to the yttrium (Y) element, which facilitates the formation of passivation films and confers a resistance effect, thereby bolstering the coatings’ resistance to corrosion. The bond strength of the high-temperature oxidation-treated CuAlY/BN coating was improved by about 30% after 960 h of salt-spray corrosion.

26 November 2024 in Ceramics International
Verified
Journal Article
Closed access
QHQing Hu
Qing Hu
ZZZhiqiang Zhong
Zhiqiang Zhong
ZHZhang Huifeng
Zhang Huifeng
CLChunfa Liao
Chunfa Liao
GXGuozuan Xu
Guozuan Xu

15 October 2019 in Metals
Verified
Journal Article
Open access
PDF file
RLRuoyu Liu
Ruoyu Liu
CHChuanbing Huang
Chuanbing Huang
LDLingzhong Du
Lingzhong Du
HLHao Lan
Hao Lan
SFShige Fang
Shige Fang
WZWeigang Zhang
Weigang Zhang
Elements’ diffusion between Ti-6Al-4V alloy and Al in the process of sliding was investigated from 400 °C to 600 °C. The results showed that the atoms were diffused at the Ti-6Al-4V/Al interface. When sliding at 400 °C and 500 °C, no intermetallic compound was detected on the surface of Ti-6Al-4V alloy. When sliding at 600 °C, intermetallic TiAl3 was formed and grew on the surface of Ti-6Al-4V alloy. The diffusion thickness of Al atoms on the surface of Ti-6Al-4V alloy increased with increasing time and temperature. The diffusion kinetic equation of Al atoms on the surface of Ti-6Al-4V alloy was successfully established. The diffusion activation energy of Al atoms in the sliding process was calculated to be 28.22 kJ·mol−1 and the dynamic index n was 0.5. The diffusion growth of Al atoms was controlled by normal parabolic law with time.