Heat energy storage is one of the most common technical solutions in the conditions of operation of low-potential and renewable energy sources. Adsorption heat energy storage devices based on the composite media “silica gel – salt” are the most effective in these conditions. The technique and technology of sol-gel synthesis of the composite adsorption materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” have been developed. A special feature of this technique is a two-stage process involving the formation of silicon phase nuclei in the interaction of aqueous solutions of silicate glass and sulphuric or acetic acids in the presence of a polymeric quaternary ammonium salt and subsequent coarsening of the particles with the gradual addition of solutions of silicate glass and the corresponding acids. The essence of the technology consists in successive stages of formation and integration of the silicic phase nuclei, hydrolysis of functional OH- groups, filtration and drying of the fine precipitate. A qualitative difference in the adsorption properties of the synthesized composites and the mechanical mixture of salt – silica gel with sorption capacity inferior to them on average by 30% is revealed by differential thermal analysis. The processes of application of the composite adsorption materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” obtained by the sol-gel method have been studied. A qualitative difference in the kinetics of adsorption of water by the composite adsorbents is shown as compared to massive salts. It is established that the amount of heat of adsorption of water vapor by the composite adsorbents of the materials “silica gel – sodium sulfate” and “silica gel – sodium acetate” is approximately 30 % greater than the linear superposition of salt and silica gel.

Heating flame furnaces are the main type of furnaces used for heating and heat treatment of metal products in metallurgy and mechanical engineering. In the working chamber of a modern heating furnace, there should be neither high-temperature nor stagnation zones. One of the methods used to provide such combustion conditions is the application of distributed (volumetric) combustion. Owing to this method, heating quality is ensured by creating a uniform temperature field and equivalent heat exchange conditions, regardless of the placement of the charge in the working chamber of the furnace. In this work, we numerically study the volumetric combustion and influences of small- and large-scale recirculation ratios of furnace gases, the influence of temperature fluctuation on the regenerator nozzle, and the working parameters at the starting phase and reverse.

The rapid spread of SARS-CoV-2 required immediate actions to control the transmission of the virus and minimize its impact on humanity. An extensive mutation rate of this viral genome contributes to the virus’ ability to quickly adapt to environmental changes, impacts transmissibility and antigenicity, and may facilitate immune escape. Therefore, it is of great interest for researchers working in vaccine development and drug design to consider the impact of mutations on virus-drug interactions. Here, we propose a multitarget drug discovery pipeline for identifying potential drug candidates which can efficiently inhibit the Receptor Binding Domain (RBD) of spike glycoproteins from different variants of SARS-CoV-2. Eight homology models of RBDs for selected variants were created and validated using reference crystal structures. We then investigated interactions between host receptor ACE2 and RBDs from nine variants of SARS-CoV-2. It led us to conclude that efficient multi-variant targeting drugs should be capable of blocking residues Q(R)493 and N487 in RBDs. Using methods of molecular docking, molecular mechanics, and molecular dynamics, we identified three lead compounds (hesperidin, narirutin, and neohesperidin) suitable for multitarget SARS-CoV-2 inhibition. These compounds are flavanone glycosides found in citrus fruits – an active ingredient of Traditional Chinese Medicines. The developed pipeline can be further used to (1) model mutants for which crystal structures are not yet available and (2) scan a more extensive library of compounds against other mutated viral proteins.

The performance of an adsorptive heat-moisture regenerator based on a silica gel–sodium sulphate composite adsorbent was studied. The correlation between the adsorbent composition and structural characteristics of the laboratory-scale device was investigated. An algorithm for the calculation of the efficiency factors of the adsorptive regenerator was further developed. The suggested algorithm calculates the operational parameters, including the temperatures, humidities and volumetric flows of internal and external air, and estimates the regenerator’s performance via temperature and moisture efficiency factors, total adsorption and time needed to achieve maximum adsorption, air pressure loss and fan power input. The validity of the calculation results obtained using the proposed algorithm was confirmed experimentally. Temperature efficiency factor, air pressure loss and fan power consumption are crucial parameters for the estimation of the optimal operating regime of an adsorptive heat-moisture regenerator. The correlation between meteorological conditions and efficiency factors was assessed and applied in a simulation of residential house-scale air conditioning unit operation. Maximal values of temperature efficiency factor were found at internal and external air temperatures of 15 to 20 °C and −5 to 0 °C, respectively. Moisture efficiency factors were observed to reach their maximum at the absolute humidities of external and internal air of 4.0 to 5.0 g/m³ and 2.75 to 3.0 g/m³, respectively. The fan power consumption of the adsorptive heat-moisture regenerator was found to be comparable to or even lower than that of commercial air conditioning units used in comparably voluminous interiors.

The self-decomposition reaction of the nickel ammonia complex was used for the nickel hydroxide formation on the nickel foam with further modification in several ways. The addition of polyvinyl pyrrolidone (PVP) and the electrochemical or chemical activation with cobalt hydroxide was used to modify the formation method. In all cases, structures with Ni(OH)₂ nanoflakes were formed. It was found that the flower-like particles of Co(OH)₂ were precipitated during chemical activation among the nanoflakes. It was shown that the presence of PVP during the nickel ammonia complex decomposition suppressed the highly branched particles. The absence of the highly branched particles increased the capacitive properties of the formed electrode at high current densities. The highest capacitance in 1408 F/g at 1 A/g was shown for the sample precipitated with the PVP presence and the further chemical activation by cobalt.

The effect of epoxidized soybean oil on the operational, technological, and physical and mechanical properties of composites based on high-density recycled polyethylene filled with wood floor was investigated. It has been shown that the introduction of epoxidized soybean oil in the amount of 0.5 wt.% into the wood-polymer composite (WPC) improves the physical, mechanical, and operational properties of the material: the Charpy impact strength (on notched samples) increases from 7.5 kJ/m² to 20.0 kJ/m², the bending strength increases from 31.6 MPa to 50.8 MPa, and the coefficient of linear thermal expansion decreases by 15%. With a further increase in the content of epoxidized soybean oil in the composite, its water absorption and technological shrinkage decrease, but its physical and mechanical properties deteriorate.