Conventional transportation systems are facing many challenges related to reducing fuel consumption, noise, and pollutants to satisfy rising environmental and economic criteria. These requirements have prompted many researchers and manufacturers in the transportation sector to look for cleaner, more efficient, and more sustainable alternatives. Powertrains based on fuel cell systems could partially or completely replace their conventional counterparts used in all modes of transport, starting from small ones, such as scooters, to large mechanisms such as commercial airplanes. Since hydrogen fuel cells (HFCs) emit only water and heat as byproducts and have higher energy conversion efficiency in comparison with other conventional systems, it has become tempting for many scholars to explore their potential for resolving the environmental and economic concerns associated with the transportation sector. This paper thoroughly reviews the principles and applications of fuel cell systems for the main transportation schemes, including scooters, bicycles, motorcycles, cars, buses, trains, and aerial vehicles. The review showed that fuel cells would soon become the powertrain of choice for most modes of transportation. For commercial long-rage airplanes, however, employing fuel cells will be limited due to the replacement of the axillary power unit (APU) in the foreseeable future. Using fuel cells to propel such large airplanes would necessitate redesigning the airplane structure to accommodate the required hydrogen tanks, which could take a bit more time.

Wingtip vortices generated from aircraft wingtips, as a result of the pressure differential at the wingtip, constitute a major component of the total drag force, especially during take-off and landing. In addition to the drag issue, these vortices also pose a significant hazard to smaller aircraft flying in the wake of the larger airplane. The wingtip vortices play a crucial role in aerodynamic efficiency, fuel consumption, flight range, and aircraft stability. This paper presents an overview of the volume of work conducted over the past six decades to encapsulate the phenomena and the techniques devised to mitigate the wingtip vortices. It is shown that the aerodynamic efficiency of the examined wingtip devices ranges from 1% to 15%, depending on the type of wingtips and the flight conditions. Furthermore, it is pointed out that the decrease in fuel consumption ranges from 3.4% to 10%, and the reduction in the induced drag ranges from 5% to 20%.

Crash boxes play a vital role in improving vehicle safety by absorbing collision energy and reducing the forces transmitted to occupants. Additive manufacturing (AM) has become a powerful method for developing advanced crash boxes by enabling complex geometries. This review provides a comprehensive examination of recent progress in AM crash boxes, with a focus on three key aspects: geometric design innovations, material behavior, and manufacturing techniques. The review investigates the influence of various AM-enabled structural configurations, including tubular, origami-inspired, lattice, and bio-inspired designs, on crashworthiness performance. Among these, bio-inspired structures exhibit superior energy absorption characteristics, achieving a mean specific energy absorption $\left(SEA\right)$ of 21.51 J/g. Material selection is also explored, covering polymers, fiber-reinforced polymers, metals, and multi-material structures. Metallic AM crash boxes demonstrate the highest energy absorption capacity, with a mean $SEA$ of 28.65 J/g. In addition, the performance of different AM technologies is evaluated, including Stereolithography (SLA), Material Jetting (MJT), Selective Laser Melting (SLM), Selective Laser Sintering (SLS), Fused Deposition Modeling (FDM), and hybrid manufacturing techniques. Among these, crash boxes produced by SLM show the most favorable energy absorption performance, with a mean $SEA$ of 16.50 J/g. The findings presented in this review offer critical insights to guide future research and development in the design and manufacturing of next-generation AM crash boxes intended to enhance vehicle safety.

In the last few years, many efforts have been devoted to investigating the antibacterial activity of metal nanoparticles, especially against multidrug-resistant bacteria. Recently extensively drug-resistant (XDR) bacteria have emerged and caused a global threat. The purpose of this manuscript was to synthesize nanostructured γ-Al₂O₃ as an antibacterial agent against some XDRs. The results showed that Al₂O₃ was a mix of rod and spherical shapes in the nano range with diameters of less than 30 nm. The zeta potential was determined to estimate the surface charge for the synthesized γ-Al₂O₃, which was recorded as −34 ± 1.8 mV, indicating good stability. The synthesized nanostructured γ-Al₂O₃ showed a potent antibacterial activity against extensively drug-resistant Acinetobacter baumanii, with an inhibition zone diameter that reached 19 mm and a minimum inhibitory concentration (MIC) value that reached 2 µg/mL. The observed antibacterial activity of the prepared Al₂O₃ nanoparticles confirmed that the main mechanistic actions include bacterial cells apoptosis, ROS increment, cellular membrane disruption, and DNA damage. The cytotoxic effect (CC50) of the prepared γ-Al₂O₃-NPs was 1250 µg/mL in a normal human lung fibroblast cell line (WI-38 cells). It can be concluded that the synthesized γ-Al₂O₃ had an acceptable toxicity, which may pave the way for its use as a potent agent in the fight against XDR bacteria.

Crash boxes play a crucial role in automotive safety by absorbing impact energy during collisions. The advancement of additive manufacturing (AM), particularly Fused Deposition Modeling (FDM), has enabled the fabrication of geometrically complex and lightweight crash boxes. This study presents a comparative evaluation of the crashworthiness performance of five FDM materials, namely, PLA+, PLA-ST, PLA-LW, PLA-CF, and PETG, across four structural configurations: Single-Cell Circle (SCC), Multi-Cell Circle (MCC), Single-Cell Square (SCS), and Multi-Cell Square (MCS). Quasi-static axial compression tests are conducted to assess the specific energy absorption $\left(SEA\right)$ and crush force efficiency $\left(CFE\right)$ of each material–geometry combination. Among the materials, PLA-CF demonstrates superior performance, with the MCC configuration achieving an $SEA$ of 22.378 ± 0.570 J/g and a $CFE$ of 0.732 ± 0.016. Multi-cell configurations consistently outperformed single-cell designs across all materials. To statistically quantify the influence of material and geometry on crash performance, a two-factor ANOVA was performed, highlighting geometry as the most significant factor across all evaluated metrics. Additionally, a comparative test with aluminum 6063-T5 demonstrates that PLA-CF offers comparable crashworthiness, with advantages in mass reduction, reduced $PCF$, and enhanced design flexibility inherent in AM. These findings provide valuable guidance for material selection and structural optimization in FDM-based crash boxes.