Flexible organic light-emitting diode display devices fabricated on polyimide (PI) substrates have more obvious residual image problems due to the abnormal threshold-voltage (Vth) shifts of a thin film transistor (TFT). In this paper, the Vth shift of TFT fabricated on a PI substrate was analyzed. We explained the worse bias stability and worse recovery of TFT with a PI substrate compared with TFT with a glass substrate, by an interlayer charging effect (Maxwell–Wagner effect) and a technology computer-aided design (Silvaco). When bias stress was applied for a long time, the interface between the PI substrate and the buffer layer will have a charging effect under the action of an electric field, and the charging charge will react on the channel and hinder the formation of the channel. We found that there are differences in the scale of charge under different voltage stress conditions, and this will result in different Vth shifts of driving TFTs for displays units.
In this study, we developed an a-InGaZnO (a-IGZO) thin film transistor (TFT) structure that inserts a sputtered AlOx intermediate layer (IL) within the active layer. The IL not only effectively blocks hydrogen (H) diffusion from the gate insulation (GI) layer to the upper region of a-IGZO but also modifies the energy band structure of the bottom channel region and creates a locally low electron concentration that counteracts the excess electron donated by diffused H. Compared to conventional TFTs, the TFT with the IL exhibits impressive electrical characteristics, including a high saturation mobility (μsat) of 14.5 cm2 V−1 s−1, an on/off current ratio (Ion/Ioff) of 6.2 × 108, and a low subthreshold swing (SS) of 0.16 V/dec. Furthermore, this structure exhibits remarkable stability under negative bias stress and negative bias illumination stress, with ΔVth values of 1.1 and 1.5 V, respectively. The integration of the IL provides a promising approach for enhancing the performance of a-IGZO TFTs, paving the way for next-generation display technologies.
1 August 2021 in Journal of Nanoelectronics and Optoelectronics
SCAPS software as a simulation tool was applied to investigate the photovoltaic performance of Cu2Zn4SnS4 (CZTS) thin film solar cells. Firstly, the influence of the work function of back contact on the open circuit voltage (Voc) and efficiency was studied, which increased with the work function and reached the maximum at 5.2 eV. The variation of the efficiency with the conduction band offset (CBO) at CZTS/CdS interface was discussed. The high efficiency of 12% can be obtained when CBO value changed from −0.1 to 0.2 eV, which means a little cliff-like or spike-like band alignment at the CZTS/CdS interface. Under a large spikelike CBO, the efficiency sharply declined because of the large barrier blocking the photo-generated carriers. Furthermore, the recombination and optical electronic characteristics were researched through the insertion of an intermediate layer at absorber/back contact and buffer/absorber interfaces. With the carrier concentration in p+-CZTS intermediate layer inserted at CZTS/Mo interface increasing from 1015 to 1018 cm−3, the Voc increased from 0.736 V to 0.850 V which promoted the efficiency from 12.03% to 15.60%. By inserting a low doped p-CZTS intermediate layer at CZTS/CdS interface, the efficiency achieved to 17.31%, which is attributed to the low recombination. At the concentration greater than 1017 cm−3, the close concentration of electron and hole resulted in the large recombination and inferior performance. The research scheme used in this paper is significant for CZTS-based or other photovoltaic solar cells.
The letter presents a new active-matrix light-emitting diode (AMLED) pixel circuit which breaks the limit that the PWM driving method combined with internal compensation is difficult to obtain the high-bit display. Based on a 10 row panel of 240 Hz, the bit is obviously improved from 3 bits to 8 bits by means of attaching another TFT to divide the equal sub-field of PWM into unequal one. Moreover, simulation results of the proposed 6T2C circuit demonstrate that the current error ratio is below 5.4% (@ Δ Vth = ± 3 V), indicating that this proposed 6T2C circuit is suitable for improving the bits and stability of display system.
The thin film solar cells based on Cu2ZnSnS4 (CZTS) compounds have been considered the potentially substitute to Cu(In,Ga)Se2 and CdTe absorbers due to its low cost, earth-abundant and non-toxic components. The present convention efficiency based on Mo/p-CZTS/n-CdS solar cell is far away from the theoritical value, which originated from the interfacial recombination at the Mo/CZTS heterojunction. In our study, we sputtered a 25nm thickness temporary Ge layer between the Mo electrode layer and the CZTS absorbed layer fabricated by spin coating, which could reduce the recombination centers and the Sn-loss. The partial Ge element would diffuse to CZTS which resulted in the formation of kesterite Cu2ZnSnGeS4 (CZTGS) thin films in which the (112) diffraction peaks shifted towards higher angle. The reason is the decreased lattice constant due to the replacement of large Sn atoms by smaller Ge atoms. The field emission scanning electron microscopy (FESEM) showed that the regularity and uniformity have been improved and the voids decreased after inserting Ge layer. The photovoltaic device (ITO/i-ZnO/CdS/CZTGS/Mo) was fabricated. The illuminated J–V characteristics showed that the open circuit voltage (Voc) increased from 513.42 to 620.71 mV, the short circuit current density (Jsc) increased from 11.57 to 12.44 mA, and the efficiency increased from 2.41 to 3.88% after inserting the Ge layer, which attribute to the decreased recombination at the Mo/CZTS contact and the broaden absorption spectra.