Advances in wearable device technology pave the way for wireless health monitoring for medical and non-medical applications. In this work, we present a wearable heart rate monitoring platform communicating in the sub-6GHz 5G ISM band. The proposed device is composed of an Aluminium Nitride (AlN) piezoelectric sensor, a patch antenna, and a custom printed circuit board (PCB) for data acquisition and transmission. The experimental results show that the presented system can acquire heart rate together with diastolic and systolic duration, which are related to heart relaxation and contraction, respectively, from the posterior tibial artery. The overall system dimension is 20 mm by 40 mm, and the total weight is 20 g, making this device suitable for daily utilization. Furthermore, the system allows the simultaneous monitoring of multiple subjects, or a single patient from multiple body locations by using only one reader. The promising results demonstrate that the proposed system is applicable to the Internet of Healthcare Things (IoHT), and particularly Integrated Clinical Environment (ICE) applications.

Through the years, inspiration from nature has taken the lead for technological development and improvement. This concept firmly applies to the design of the antennas, whose performances receive a relevant boost due to the implementation of bio-inspired geometries. In particular, this idea holds in the present scenario, where antennas working in the higher frequency range (5G and mm-wave), require wide bandwidth and high gain; nonetheless, ease of fabrication and rapid production still have their importance. To this aim, polymer-based 3D antennas, such as Dielectric Resonator Antennas (DRAs) have been considered as suitable for fulfilling antenna performance and fabrication requirements. Differently from numerous works related to planar-metal-based antenna development, bio-inspired DRAs for 5G and mm-wave applications are at their beginning. In this scenario, the present paper proposes the analysis and optimization of a bio-inspired Spiral shell DRA (SsDRA) implemented by means of Gielis’ superformula, with the goal of boosting the antenna bandwidth. The optimized SsDRA geometrical parameters were also determined and discussed based on its fabrication feasibility exploiting Additive Manufacturing technologies. The results proved that the SsDRA provides relevant bandwidth, about 2 GHz wide, and satisfactory gain (3.7 dBi and 5 dBi, respectively) at two different frequencies, 3.5 GHz and 5.5 GHz.

Bio-inspired Dielectric Resonator Antennas (DRAs) are engaging more and more attention from the scientific community due to their exceptional wideband characteristic, which is especially desirable for the implementation of 5G communications. Nonetheless, since these antennas exhibit peculiar geometries in their micro-features, high dimensional accuracy must be accomplished via the selection of the most suitable fabrication process. In this study, the challenges to the manufacturing process presented by the wideband Spiral shell Dielectric Resonator Antenna (SsDRA), based on the Gielis superformula, are addressed. Three prototypes, made of three different photopolymer resins, were manufactured by bottom-up micro-Stereolithography (SLA). This process allows to cope with SsDRA’s fabrication criticalities, especially concerning the wavy features characterizing the thin spiral surface and the micro-features located in close proximity to the spiral origin. The assembly of the SsDRAs with a ground plane and feed probe was also accurately managed in order to guarantee reliable and repeatable measurements. The scattering parameter S₁₁ trends were then measured by means of a Vector Network Analyzer, while the realized gains and 3D radiation diagrams were measured in the anechoic chamber. The experimental results show that all SsDRAs display relevant wideband behavior of 2 GHz at −10 dB in the sub-6 GHz range.

Sensing systems are becoming less and less invasive. In this context, flexible materials offer new opportunities that are impossible to achieve with bulky and rigid chips. Standard silicon sensors cannot be adapted to curved shapes and are susceptible to big deformations, thus discouraging their use in wearable applications. Another step forward toward minimising the impacts of the sensors can be to avoid the use of cables and connectors by exploiting wireless transmissions at ultra-high frequencies (UHFs). Thin-film bulk acoustic wave resonators (FBARs) represent the most promising choice among all of the piezoelectric microelectromechanical system (MEMS) resonators for the climbing of radio frequencies. Accordingly, the fabrication of FBARs on flexible and wearable substrates represents a strategic step toward obtaining a new generation of highly sensitive wireless sensors. In this work, we propose the design and fabrication of a flexible gravimetric sensor based on an FBAR on a polymeric substrate. The resonator presents one of the highest electromechanical coupling factors in the category of flexible AlN-based FBARs, equal to 6%. Moreover, thanks to the polymeric support layer, the presence of membranes can be avoided, which leads to a faster and cheaper fabrication process and higher robustness of the structure. The mass sensitivity of the device was evaluated, obtaining a promising value of 23.31 ppm/pg. We strongly believe that these results can pave the way to a new class of wearable MEMS sensors that exploit ultra-high-frequency (UHF) transmissions.

In this paper, a minimally invasive dielectric sensor with a compact footprint of 24x18 mm2 is presented. It is based on two complementary split ring resonators (CSRRs) fed by a microstrip with coplanar waveguide configuration and placed on a 200 μm thick Kapton substrate. The device has been fabricated by means of a multi-material 3D printer NanoDimension’s Dragonfly IV and is characterized by exploiting two different sensing methodologies. As a first step, the device has been characterized in the air by measuring the volume of deionized water droplets placed on one of the CSRRs in the range between 3.6 μl and 9.6 μl. This study has been performed through the analysis of the resonant frequency shift caused by the variation of the dielectric constant. The results show a Q-factor of 702 and a sensitivity of 0.3% μl-1. Then, an additional step has been carried out for the measurement of the temperature of the water in which the sensor is totally dipped. We analyzed the frequency shift due to the water temperature variation in the range between 20°C and 40°C which corresponds to a variation in relative permittivity. In this case, the sensor shows remarkable results in terms of Q-factor, equal to 501, and a sensitivity to dielectric variations in out-of-body and in-body temperature ranges equal to 0.5% and 1.5%, respectively.

Realizing thin-film acoustic wave resonators presents many design and fabrication challenges. Actual material specifications always differ from nominal material properties employed in simulations, as they depend on the deposition technique and parameters used and on equipment type and status. Moreover, each deposition process introduces a degree of uncertainty regarding the thicknesses of the layers. All these factors have a substantial impact on the resonance frequency, which often differs from the designed value. This work details the design and fabrication of an aluminum nitride (AlN)-based thin-Film Bulk Acoustic wave Resonator (FBAR) showing one of the highest products of Q-factor and electromechanical coupling of 6895. The design process is based on an innovative, fast, and scalable design and fabrication approach that considers fabrication tolerances. The algorithm returns very fast results on the order of seconds, and successfully estimates the resonance of a designed stack at 2.55 GHz with a very low error of 0.005 GHz (about 0.2%). The FBAR layer stack is suspended on a polymeric membrane and an innovative rapid dissolving sacrificial layer made of Lift-Off Resist (LOR). This new fabrication protocol obtains resonators with an electromechanical coupling factor of 4.7% and a maximum quality factor of 1467, respectively.