The treatment and disposal of sewage sludge is one of the most important and critical issues of wastewater treatment plants. One option for sludge liquidation is the production of fuel in the form of pellets from mixed sewage and paper mill sludge. This study presents the results of the combustion of pelletized fuels, namely sewage and paper mill sludge, and their 2:1 and 4:1 blends in a fluidized bed combustor. The flue gas was analysed after reaching a steady state at bed temperatures of 700–800 °C. Commonly used flue gas cleaning is still necessary, especially for SO2; therefore, it is worth mentioning that the addition of paper mill sludge reduced the mercury concentration in the flue gas to limits acceptable in most EU countries. The analysis of ash after combustion showed that magnesium, potassium, calcium, chromium, copper, zinc, arsenic, and lead remained mostly in the ash after combustion, while all cadmium from all fuels used was transferred into the flue gas together with a substantial part of chlorine and mercury. The pellets containing both sewage and paper mill sludge can be used as an environmentally friendly alternative fuel for fluidised bed combustion. The levelized cost of this alternative fuel is at the same current price level as lignite.
The process of gasification is well-known; however, to this day, the applications of such facilities, especially off-grid small-scale units for direct electricity and char production, are scarce. In this study, an off-grid fixed bed downdraft gasification unit is studied from the gaseous/solid product character perspective. This unit represents a possible solution for the emerging call for sustainable decentralised energy sources. Softwood chips were utilised in this study, and their conversion into synthetic gas (direct electricity supply) and solid biochar was observed and analysed. The results show promising values of synthetic gas for potential utilisation in different applications outside the direct combustion process, such as microbial syngas fermentation, with a lower heating value equal to 6.31 MJ·m-3. It appears that during the steam activation process of biochar, both high-quality off-gas of more than 70%vol. H2 (excluding N2) and activated carbon of a specific surface area of 565.87 m2·g-1 can be collected. Further investigations have revealed specific degradation of chemical bonds and material morphology changes during steam gasification. The microporous structure and high specific surface area of the material make it an attractive material for further development as an adsorbent in sorption cooling devices. Therefore, the waste generated within the gasification process is minimised, and the potential of the obtained products will be valued in favour of the sustainability of the remote locations.
Due to the outdated higher requirements for reducing emissions of harmful substances in the combustion of fossil fuels and waste in particular, more and more research is needed, which will lead to the provision of various alternatives to influence the emerging pollutants into the atmosphere. This study deals with the development of experimental combustion units with a stationary fluidized bed with regulated parameters of primary and secondary air supply, performed fuel supply and flue gas parameters. Combustion is carried out in a bubbling stationary fluidized bed with a height of 100 mm and a diameter of 140 mm. The fluidized bed consists of ST 54 glass sand with a mean grain size of 0.22 mm. The basic purpose of the study is to describe the construction of the experimental unit with verification of its functionality. On the experimental equipment was realized experiments in terms of combustion various types of fuels, whether they are fossil fuels (coal), alternative fuels as straw pellets, sludge from wastewater treatment plants, sludge from paper mills or their combinations. Determination of temperature and pressure along the entire length of the unit is a device equipped with thermocouples and pressure sensors.
11 April 2024 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Cellulose acetate (CA) mixed-matrix membranes incorporating polyvinylpyrrolidone (PVP), bentonite (B or Ben), graphene oxide (GO), and titanium dioxide (TiO2) were prepared by the phase inversion separation technique for oil/water separation. An investigation was performed where the mixed-matrix membrane was tested for the separation performance of hydrophilic and hydrophobic surface properties. An ultrafiltration experiment at the laboratory scale was used to test dead-end ultrafiltration models developed for the treatment performances of oily wastewater under dynamic full-scale operating conditions. Artificial oily wastewater solutions were prepared from hexane, toluene, and engine oil with Tween80 emulsions for oil removal treatment using composite membranes. The impacts of material hydrophilicity, weight loss, permeability, and pore size were investigated, and it was found that the oil retention of membranes with larger pore sizes enabled much more sophisticated water flux. The CA-GO-, CA-B-, and CA-TiO2-incorporated membranes achieved pure water flux (PWF) values of 45.19, 53.41, and 100.25 L/m2h, respectively. The performance of CA-TiO2 in oil/water emulsion rejection was assessed, and the rejection of engine oil/water, toluene/water, and hexane/water mixtures was determined to be 95.21%, 90.33%, and 92.4%, respectively. The CA-based mixed-matrix membrane portrayed better antifouling properties due to enhanced hydrophilicity and water molecules. The CA-TiO2-incorporated membrane possessed the potential to provide high separation efficiency for oily wastewater treatment. This study demonstrates the potential of fine-tuning membrane performances through material hybridization to achieve efficient wastewater treatment.