Bohumil Skala

Prof. Dr. Bohumil Skala

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 March 2015 in MM Science Journal
Verified
Journal Article
Open access
RPRoman Pechanek
Roman Pechanek
VKVladimir Kindl
Vladimir Kindl
BSBohumil Skala
Bohumil Skala

22 March 2025 in Electrical Engineering
Verified
Journal Article
Open access
PDF file
MZMartin Zavřel
Martin Zavřel
VKVladimir Kindl
Vladimir Kindl
Michal FrivaldskyMichal Frivaldsky
Michal Frivaldsky
BSBohumil Skala
Bohumil Skala
Presented paper discusses power distribution bus of dynamic wireless charging track for e-mobility applications. The focus is applied to the matrix converter and AC power distribution bus adaptation. The key behavior of matrix one-to-one phase converter and three-to-one phase converter is presented to get topologies for adaptation. Get matrix converter features are discussed regarding to the wireless power transfer and dynamic charging in electromobility. Feasibility of power topologies and control approaches are discussed as well. Proposed dynamic charging using three-phase matrix converter adaptation is compared to the conventional topologies using DC power distribution bus and corresponding inverters topologies. Knowledge taken from literature and theoretical discussion is verified by MATLAB–Simulink simulations and by basic experiments. Finally, feasibility study decisions are made in conclusion.

16 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
VKVaclav Kus
Vaclav Kus
BSBohumil Skala
Bohumil Skala
PDPavel Drabek
Pavel Drabek
The paper deals with a new methodology for calculating the filter parameters. The basis is respect for the fact that the real filter current consists of other harmonic components, which filter is tuned. The proposed methodology was used to design filters for traction substation 25 kV/50 Hz. The operation of the locomotives in the AC supply systems of 25 kV/50 Hz leads to a rising of higher order harmonic currents. Due to the 1-phase supply system, these are mainly the 3rd and 5th harmonics. By simulation and subsequent measurement of the proposed traction power station filters the proposed methodology was verified. Thus, the filter design can also be used for filter compensating stations of the standard 3-phase distribution network. The described method presents an optimal filter design without unnecessary oversizing. This fact reduces the size and cost of the filter. It is shown that it is possible to design a filter that meets the requirements for power quality under extreme load and to minimise distortion of line voltage.

24 April 2026 in Machines
Verified
Journal Article
Open access
PDF file
Jiri SikaJiri Sika
Jiri Sika
MKMichal Křížek
Michal Křížek
TKTomáš Kavalír
Tomáš Kavalír
BSBohumil Skala
Bohumil Skala
This study addresses the premature failure of electric motor bearings caused by inverter-induced parasitic currents. We propose a novel segmented end shield design utilizing 24 carbon fiber-reinforced polymer (CFRP) lamellae to provide both structural support and galvanic isolation. The “main working” of the design relies on a segmented architecture where the lamellae are adhesively bonded between a central bearing housing and an outer mounting flange, creating a high-impedance path that interrupts circulating currents. Experimental validation focused on both mechanical stability and dielectric performance. Results indicate that the assembly maintains rotor positional integrity under nominal loads while providing an insulation resistance > 1 GΩ at 1 kV and a structural capacitance of 2.47 nF. These parameters effectively mitigate low-frequency circulating currents. Data analysis, derived from the mean values of repeated test cycles, confirms that the composite architecture serves as a viable, mechanically robust alternative to conventional metallic end shields.

1 December 2021 in Electrical Engineering
Verified
Journal Article
Closed access
PDF file
BSBohumil Skala
Bohumil Skala
VKVladimir Kindl
Vladimir Kindl
Michal FrivaldskyMichal Frivaldsky
Michal Frivaldsky

19 March 2025 in Electrical Engineering
Verified
Journal Article
Open access
PDF file
BSBohumil Skala
Bohumil Skala
VKVladimir Kindl
Vladimir Kindl
Michal FrivaldskyMichal Frivaldsky
Michal Frivaldsky
LSLukas Sobotka
Lukas Sobotka
MZMartin Zavrel
Martin Zavrel
This paper investigates the influence of an asymmetrical power supply on induction machines, focusing on key parameters such as temperature rise, torque, efficiency, and power factor. Various three-phase voltage asymmetries are examined to determine their impact on the magnitude of the negative-sequence voltage component. The study further explores how a drop in phase voltage leads to a significant negative component, the effect of phasor rotation from its ideal position, and the number of phases subject to voltage drops or phase shift errors. A voltage synthesis approach is employed to analyse the roles of the positive and negative components, with one component held constant to evaluate the resulting changes in power factor, efficiency, and torque. In addition, a dynamic thermal model is implemented to assess the machine’s temperature rise under load conditions.