Frame structures equipped with steel plate shear walls (SPSWs) have been widely used in high-rise buildings due to their good seismic performance. In this study, the strip model and combined strip model were used to analyze the performance of SPSWs. Furthermore, an improved genetic algorithm (IGA) was established to optimize the steel frame for 5, 10, and 20 stories. For each layer, layout optimization was conducted to determine the best configurations of the SPSWs, and two cases of size optimizations of conventional SPSW configurations in the frame were conducted. Results indicate the following: (i) the total weight of the five-story steel frame of layout optimization to determine the best SPSW configuration was approximately 10% lighter than those of the size optimization of conventional SPSW configurations, and this proportion gap expanded to approximately 15–25% for the 10-story and 20-story steel frames; (ii) the steel frame weight could be significantly reduced if the average percentages of story shear resisted by web plates are increased; and (iii) in the steel frame of layout optimization, the structural elements, especially the plate elements, were better utilized than those of size optimization when their inter-story drift ratios met the specification requirements. These results highlight the prominent performances of some important indicators of the design of an SPSW system with the layout optimized using IGA.
The welds of T-joints are prone to fatigue cracking owing to stress concentrations and welding residual stresses. Previous studies investigated the crack propagation rate using numerical simulations; however, most employed two-dimensional models and ignored the effect of residual stresses. In this study, reliable temperature and residual stress fields were obtained through numerical simulations and verified experimentally. The effects of residual stresses on crack propagation were then investigated under different loading conditions. The residual stress field caused the direction of crack propagation to shift towards the web and accelerated the crack propagation speed with increasing displacement loading.
Based on stochastic sensitivity analysis, a new style of joint structure with greater ductility and higher strength—the beam‐column joint with gusset plate angle (JGA) steel—was proposed. Research on the static and hysteretic behavior of the JGA was performed using finite element analysis and experimental methods. The research results indicated that adding a seat angle could increase the positive and negative initial rotational stiffness and strength and provide a better energy consumption performance of the joint. An improved chaotic particle swarm optimization (ICPSO) neural network algorithm was used to study the stochastic sensitivity. Seven important parameters that influence the bending stiffness and strength of the JGA, namely, the beam height, beam flange width, beam web thickness, gusset plate thickness, connection angle steel thickness, connection angle steel width, and seat angle steel thickness, were investigated by stochastic sensitivity analysis. Moreover, the beam height, connection angle steel, and seat angle steel thickness, which had significant influences on the mechanical properties of the joints, were studied in depth by finite element analysis. Within the range of the parameters of the joint, the higher the beam height was, the larger the connection angle thickness was; the smaller the connection angle width was, the better the joint performance was. A reasonable design of the JGA is proposed: a beam with the SH2 section (250 × 125 × 6 × 9 mm) and a 10 mm thick and 75 mm long angle steel connection.
There is wide use of beam-column joint with gusset plate angle connection in engineering, however, the mechanical properties of these joints are still lack of complete theoretical and experimental research. This kind of joint is often simplified as an articulated connection or other types of connections in the design. In this paper, experimental study and finite element analysis are carried out to study the flexural behavior of the beam-column joint with gusset plate angle connection. The finite element analysis is used to analyze the differences between the beam-column joint with gusset plate and other joints. The moments-rotation curves and failure modes of the three kinds of beam-column joints were obtained by the static test which were carried out. A more reasonable design of beam-column joint with angle plate of gusset plate is put forward through the research of this paper: the deformation of the column flange is restricted after adding the stiffener, which can avoid the premature yield of the column flange and making the joint have good energy dissipation capacity.
1 September 2019 in IOP Conference Series: Earth and Environmental Science
The huge economic costs with the experimental analysis and computationally expensive with the simulation are the difficulties for the stochastic analysis of engineering structures. The structural data of stochastic analysis is based on the probability of statistical results. Therefore, the focus of structural stochastic analysis is how to simulate the finite element model or the physical model by the method of approximate model with the requirements of the expected accuracy range. For the higher precision sensitivity coefficients, a large number of finite element simulations would be conducted and this process leads to intensive computation. This paper puts forward a methodology that combines the high dimensional model representation(HDMR) method and the hybrid neural network for the approximate model. The advantage of this method is the determination of coupling characteristics of the input parameters, and the complex multidimensional model could be constructed by the limited sample points. The feasibility of the method was applied to semi-rigid connection with multidimensional parameter, and the efficiency and precision were obviously superior to the traditional approximate method.
Two types of lateral resistance structural systems, namely unstiffened steel plate shear walls (USPSWs) and stiffened steel plate shear walls (SSPSWs), are typically used in high-rise structures. Numerous experimental and numerical studies have been conducted on the structural performance of SSPSWs. However, few studies have been conducted to investigate the effect of column flexural stiffness on SSPSW systems. In this study, an analysis and numerical investigation of SSPSWs with variable column flexural stiffnesses was performed. The hysteretic performance, secant stiffness reduction and energy dissipation of SSPSWs with four column flexural stiffnesses were investigated. The column flexural stiffness reduction in the USPSWs and SSPSWs did not negatively influence the overall performance of drift ratios up to 2.5%. Moreover, the infill plates of the USPSWs and SSPSWs could achieve the ultimate strengths similar to the theoretical values despite the column not satisfying the minimum flexural stiffness requirements from CSA S16-09 and PEER/ATC72-1, which indicated that these requirements could be conservative.