Binder free vertical aligned (VA) CNT/sulfur composite electrodes with high sulfur loadings up to 70 wt% were synthesized delivering discharge capacities higher than 800 mAh g−1 of the total composite electrode mass.
A low‐density electrolyte composition is introduced for lithium–sulfur (Li–S) batteries with intrinsic and effective polysulfide shuttle suppression. Hexyl methyl ether (HME) is used in combination with 1,3‐dioxolane (DOL) as a solvent for the Li–S battery electrolyte. The choice of solvent limits the dissolution of polysulfides, leading to successful suppression of the parasitic polysulfide shuttle. Hence, high coulombic efficiencies of 98% can be obtained in coin cells for over 50 cycles. The impact of the specifically adapted electrolyte solvent is studied systematically by varying solvent combinations in order to enable the development of light innovative shuttle suppressing electrolytes. In contrast to concepts relying on hydrofluoro ether dilution, the presented electrolyte features a significantly reduced mass density at 2 m lithium bis(trifluoromethanesulfonylimide) (LiTFSI) conductive salt enabling significant weight reduction on the Li–S prototype cell level, thus, allowing energy densities up to 400 Wh kg−1.
25 September 2019 in Journal of the Electrochemical Society
In recent years, both silicon thin films and nickel-rich layered oxides have received much attention as promising anode or cathode materials for next generation lithium ion batteries, respectively. In this work, full cells containing Li[Ni0.8Co0.1Mn0.1]O2 (NCM811) as cathode in combination with amorphous columnar silicon thin films as anode are evaluated in coin cells and 3-electrode cells with varying capacity balancing. Full cells with area capacity ratios of negative to positive electrodes (n/p-ratio) reaching from 1.15 : 1 to 2.70 : 1 are studied. The cells with a high n/p-ratio (2.00 : 1 and 2.70 : 1) show significantly lower specific capacity of 115 mA h gNCM−1 after 50 cycles of galvanostatic cycling in comparison to 130 mA h gNCM−1 for a cell with a n/p-ratio of 1.15 : 1. One reason for this phenomenon is the decline of the initial coulombic efficiency with increasing n/p-ratios. Secondly, through only partial utilization of the silicon anode by using high n/p-ratios, the anode potential is increased at the end of charge. This leads to a higher cathode potential and therefore a faster degradation of the cell. In summary, for designing high performance NCM811/Si full cells, high n/p-ratios should be avoided.
All‐solid‐state batteries (SSB) show great promise for the advancement of high‐energy batteries. To maximize the energy density, a key research interest lies in the development of ultrathin and highly conductive solid electrolyte (SE) layers. In this work, thin and flexible sulfide solid electrolyte membranes are fabricated and laminated onto a non‐woven fabric using a scalable and solvent‐free, continuous roll‐to‐roll process (DRYtraec). These membranes show significantly improved tensile strength compared to unsupported sheets, which facilitates cell assembly and allows a continuous component production using a single‐step calendering process. By tuning the thickness, densified membranes with thicknesses ranging from 40 to 160 µm are obtained after a compression step. The resulting SE membranes retain a high ionic conductivity (1.6 mS cm−1) at room temperature. An excellent rate capability is demonstrated in a SSB pouch cell with a Li2O–ZrO2‐coated LiNi0.9C0.05Mn0.05O2 cathode, a 55 µm thin SE membrane, and a columnar silicon anode fabricated by a scalable physical vapor deposition process. At stack level, a promising energy density of 673 Wh L−1 (and specific energy of 247 Wh kg−1) is achieved, showcasing the potential for high energy densities by reducing the SE membrane thickness while retaining good mechanical properties.
Lithium–sulfur batteries with liquid electrolytes are discussed as the most promising post‐lithium‐ion‐battery technology in literature due to their high theoretical specific energy and first prototype cells delivering >470 Wh kg−1. Although several electrolyte and material concepts are developed that partially solve the issue of the so‐called shuttle mechanism, the most promising concept to genuinely confine sulfur species in the cathode is all‐solid‐state argyrodite–sulfur cathodes leading to almost theoretical active material utilization by maintaining reasonable sulfur loadings and electrolyte to sulfur ratios. However, this battery concept has so far not achieved reversible cycling against metallic lithium anodes as it requires high pressures for manufacturing, and ductile lithium metal creeps along the grain boundaries of the solid electrolyte particles leading to short cuts of the cells. Recent findings show that metallic lithium, however, can be stably cycled with dimethoxyethane/lithium‐bis(fluorosulfonyl)imide (DME/LiFSI)‐based electrolytes. Herein, for the first time, a semisolid concept is presented combining the benefits of an argyrodite‐based solid‐state cathode and a DME/LiFSI/hydrofluoroether‐based anolyte concept – in coin cells and first pouch cells. This disruptive approach enables projected specific energies higher than 600 Wh kg−1 at cell stack level.