Introduction. When studying composite materials for construction purposes, it is needed to consider the mechanisms of formation of the structure and properties of modern concretes in the process of strength development. In studies of modern composite materials based on cement binder, there is no information about the development of structural defects and destruction of the material at the initial stages of strength development. This information can be obtained using X-ray computed tomography, a promising method of nondestructive testing of the state of the material. Therefore, the objective of this work was to study the formation and propagation of cracks in samples of fine-grained concrete with different fractional composition of sand due to natural processes of cement shrinkage, as well as the mechanics of destruction of samples of modified fine-grained concrete when applying a compressive load at the early stages of strength development. Materials and Methods. The study used fine-grained concrete mixtures of three compositions with different sand gradation. The tomography samples were made by placing fresh mixtures in polymer cylindrical containers. Tomography of the samples immediately after manufacture, as well as after 8 and 51 days, was performed in a YXLON Cheetah microfocus X-ray machine. The composition with two-fraction sand was modified by mechanical activation of the components, 20×20×20 mm cube samples were made. Further, compression tests were performed at the Instron installation after 3 and 7.5 hours, and then — tomography of the destroyed samples.Results. It was established that the destruction of contact zones depended on the ratio of the size of the fractions. In the presence of a bulk of coarse sand grains in concrete, the destruction of contact zones was more pronounced and had a main mode. When using fine or polyfraction sand, contact zones were destroyed locally and had a visually smaller area. The images of the destroyed modified sample, tested 3 hours after manufacturing, showed clear cracks and indents on the edges, which indicated the elastic-plastic nature of the destruction. In 7.5 hours, the edges of the sample upon destruction were covered with a network of small cracks; inside the sample there were also numerous cracks and microcracks, which indicated brittle fracture. Based on the obtained images of the deformed structure of modified concrete, the mechanism of transition from elastic-plastic destruction of the material to brittle one was clearly visible.Discussion and Conclusion. The studied dependences of the influence of the size of fine aggregate on the mechanisms of formation and propagation of structural defects contribute to the theory of the processes of destruction of fine-grained concretes. The results obtained prove the prospects of using X-ray computed tomography as a method of nondestructive testing of the internal structure of fine-grained concrete, including at the early stages of strength development.
The most massive design on the Baltic shore used geosynthetic materials, the landslide protection construction in Svetlogorsk (1300 m long, 90,000 m2 area, South-Eastern Baltic, Kaliningrad Oblast, Russian Federation) comprises the geotextile and the erosion control geomat coating the open-air cliff slopes. Due to changes in elastic properties during long-term use in the open air, as well as due to its huge size, this structure can become a non-negligible source of microplastic pollution in the Baltic Sea. Weather conditions affected the functioning of the structure, so it was assessed that geosynthetic materials used in this outdoor (open-air) operation in coastal protection structures degraded over time. Samples taken at points with different ambient conditions (groundwater outlet; arid places; exposure to the direct sun; grass cover; under landslide) were tested on crystallinity and strain at break. Tests showed a 39–85% loss of elasticity of the polymer filaments after 3 years of use under natural conditions. Specimens exposed to sunlight are less elastic and more prone to fail, but not as much as samples taken from shaded areas in the grass and under the landslide, which were the most brittle.
The possibility of complex experimental study of the structure and properties of modern multicomponent concretes combining the influence of mechanical activation of the initial powder components of building mixtures, the rheology of concrete solutions, the structure of the concrete mixture, the distribution of various components and pores, the nature of damage and destruction at various stages of concrete strength testing is considered. The classical set of experimental methods for studying the rheological characteristics and strength of concretes at various setting stages is supplemented by studies of the concrete structure using X-ray computed tomography. The developing approach allows to solve the fundamental problems of building material science of concrete.
A computer simulation approach to sintering of low-temperature ceramics has been developed within the framework of the micromechanics of heterogeneous media. It is taken into account that the...
1 August 2019 in IOP Conference Series: Materials Science and Engineering
The paper shows the promising use of sea sand for additive technologies in construction. The use of sea sand reduces the setting time of the concrete mix and increases the initial strength compared to conventional quarry construction sand. A comparative analysis of the characteristics of sea and quarry sands was performed. It has been experimentally proven that the use of sea sand instead of quarry sand in fine-grained concrete mix leads to a decrease in the setting time of the fresh mix and an increase in the strength of concrete samples. The flexural strength and compressive strength of samples containing sea sand at the age of 28 days increases by 35.7% and 16.7%, respectively, comparing to samples containing quarry sand.
Introduction. The development of approaches to assessing structural characteristics of multicomponent modified concretes using non-destructive testing methods at all stages of hydration is a relevant means focused on ensuring optimal rheological and strength characteristics of concretes. Materials and methods. Modified fine-grained concrete was analyzed as the material under study, since its composition meets the requirements of additive technologies applied in the construction industry. Modification was implemented by introducing additives and mechanically activating the initial cement-sand composition. The strength of resulting specimens was controlled as of the onset of curing. Structure formation was studied using a computed tomography scanner. Results. A tomography data processing approach was developed to evaluate the modified concrete’s structure. Key aspects of the stage-by-stage processing of specimens’ images were identified and a solution was obtained for determining the threshold values of correspondence between image shades having different density structures. In the course of comparing the results of the strength and structure study, the value of the percentage ratio of inclusions was obtained for various densities during the curing process. Conclusions. The proposed data acquisition approach contributes to development of further research in this area; it can become a stage in developing a new concrete structure analysis method. The study of specimens at early curing stages in combination with non-destructive control methods contributes to (1) development of rapid assessment techniques, applied to the quality of materials, and (2) an efficiency increase in the process of development.