This paper presents an eight-channel time-interleaved (TI) 2.6 GS/s 8-bit successive approximation register (SAR) analog-to-digital converter (ADC) prototype in a 55-nm complementary metal-oxide-semiconductor (CMOS) process. The channel-selection-embedded bootstrap switch is adopted to perform sampling times synchronization using the full-speed master clock to suppress the time skew between channels. Based on the segmented pre-quantization and bypass switching scheme, double alternate comparators clocked asynchronously with background offset calibration are utilized in sub-channel SAR ADC to achieve high speed and low power. Measurement results show that the signal-to-noise-and-distortion ratio (SNDR) of the ADC is above 38.2 dB up to 500 MHz input frequency and above 31.8 dB across the entire first Nyquist zone. The differential non-linearity (DNL) and integral non-linearity (INL) are +0.93/−0.85 LSB and +0.71/−0.91 LSB, respectively. The ADC consumes 60 mW from a 1.2 V supply, occupies an area of 400 μm × 550 μm, and exhibits a figure-of-merit (FoM) of 348 fJ/conversion-step.

This paper presents a real-time output 56 GS/s 8 bit time-interleaved analog-to-digital converter (ADC), where the full-speed converted data are output by 16-lane transmitters. A 64-way 8 bit asynchronous SAR array using monotonous and split switching strategy with 1 bit redundancy is utilized to achieve a high linearity and high-power efficiency. A low-power ring voltage-controlled oscillator-based injection-locked phase-locked loop combining with a phase interpolator-based time-skew adjuster is developed to generate the 8 equally spaced sampling phases. Digital gain correction, digital-detection-analog-correction offset calibration, and coarse–fine two-step time-skew calibration are combined to optimize the ADC’s performances. An edge detector and phase selector associated with a common near-end data-transmission position and far-end data-collection instant are designed to avoid reset competition and implement deterministic latency. Fabricated in a 28 nm CMOS process, the prototype ADC achieves an outstanding SNDR of 36.38 dB at 56 GS/s with a 19.9 GHz input, where 7.25 dB and 9.33 dB are optimized by offset-gain calibration and time-skew calibration, respectively. The ADC core occupies an area of 1.2 mm² and consumes 432 mW power consumption.

This paper presents a four-channel time-interleaved 3GSps 12-bit pipelined analog-to-digital converter (ADC). The combination of master clock sampling and delay-adjusting is adopted to remove the time skew due to channel mismatches. An early comparison scheme is used to minimize the non-overlapping time, where a custom-designed latch is developed to replace the typical non-overlapping clock generator. By using the dither capacitor to generate an equivalent direct current input, a zero-input-based calibration is developed to correct the capacitor mismatch and inter-stage gain error. Fabricated in a 40 nm CMOS process, the ADC achieves a signal-to-noise-and-distortion ratio (SNDR) of 57.8 dB and a spurious free dynamic range (SFDR) of 72 dB with a 23 MHz input tone. It can achieve an SNDR above 52.3 dB and an SFDR above 61.5 dB across the entire first Nyquist zone. The differential and integral nonlinearities are −0.93/+0.73 least significant bit (LSB) and −2.8/+4.3 LSB, respectively. The ADC consumes 450 mW powered at 1.8V, occupies an active area of 3 mm × 1.3 mm. The calculated Walden figure of merit reaches 0.44 pJ/step.

This paper presents a 4-bit 36 GS/s analog-to-digital converter (ADC) employing eight time-interleaved (TI) flash sub-ADCs in 40 nm complementary metal-oxide-semiconductor (CMOS) process. A wideband front-end matching circuit based on a peaking inductor is designed to increase the analog input bandwidth to 18 GHz. A novel offset calibration that can achieve quick detection and accurate correction without affecting the speed of the comparator is proposed, guaranteeing the high-speed operation of the ADC. A clock distribution circuit based on CMOS and current mode logic (CML) is implemented in the proposed ADC, which not only maintains the speed and quality of the high-speed clock, but also reduces the overall power consumption. A timing mismatch calibration is integrated into the chip to achieve fast timing mismatch detection of the input signal which is bandlimited to the Nyquist frequency for the complete ADC system. The experimental results show that the differential nonlinearity (DNL) and integral nonlinearity (INL) are −0.28/+0.22 least significant bit (LSB) and −0.19/+0.16 LSB, respectively. The signal-to-noise-and-distortion ratio (SNDR) is above 22.5 dB and the spurious free dynamic range (SFDR) is better than 35 dB at 1.2 GHz. An SFDR above 24.5 dB and an SNDR above 18.6 dB across the entire Nyquist frequency can be achieved. With a die size of 2.96 mm * 1.8 mm, the ADC consumes 780 mW from the 0.9/1.2/1.8 V power supply.

A 3GS/s 12-bit current-steering digital-to-analog converter (DAC) fabricated in 55 nm complementary metal–oxide–semiconductor (CMOS) technology has been presented. A partial randomization dynamic element matching (PRDEM) method based on switching sequence optimization is proposed to mitigate the mismatch effect and suppress the harmonic distortion with low hardware complexity. In the switching current cell, the cascode structure together with “always-ON” small current sources are used to keep the output impedance high and uniform. A compact layout of the switching current array is carefully designed, featuring short wires routing and small parasitic capacitance. According to the measured results at 3GS/s, this DAC demonstrates a spurious-free dynamic range (SFDR) of 74.64 dBc at low frequency and 50 dBc at 1.5 GHz output. The chip occupies an active area of 0.2 × 0.48 mm² and consumes a total power of 495 mW.

This paper presents a 12-bit 2.4 GS/s analog-to-digital converter (ADC) employing four time-interleaved (TI) pipelined channels with a novel on-chip timing mismatch calibration in 40 nm CMOS process. TI architecture can increase the effective sampling rate of ADC but the dynamic performance of TI-ADC system is seriously degraded by offset, gain, and timing mismatches among the channels. Timing mismatch is the most challenging barrier among these mismatches due to the difficulty and complexity of its detection and correction. An automatic wideband timing mismatch detection algorithm is proposed for achieving a wide frequency range of timing mismatch detection without complex calculations. By adopting the proposed mismatch-free variable delay line (VDL), the full-scale traversal timing mismatch correction accomplishes an accurate result without missing codes. Measurement results show that the spurious free dynamic range (SFDR) of the prototype ADC is improved from 55.2 dB to 72.8 dB after calibration at 2.4 GS/s with a 141 MHz input signal. It can achieve an SFDR above 60 dB across the entire first Nyquist band based on the timing mismatch calibration and retiming technology. The prototype ADC chip occupies an area of 3 mm × 3 mm and it consumes 420 mW from a 1.8 V supply.