Hardfacing is commonly used in parts recovery and in obtaining surfaces with improved properties. Within this field, it is important to analyze the effect of alloying elements on the properties of the deposited layers. One of the critical parameters affecting alloying performances in SMAW is improper arc length. This article examines the effect of the addition of niobium in different quantities (0, 2, 4, 6, and 8% by weight) to the electrode coating in Fe-Cr-C shielded metal arc welding (SMAW), with short and long arc lengths, on the operational process efficiency, dilution, arc energy, microstructure, and microhardness of the deposited layers. A decrease in operational process efficiency and dilution was found with increases in niobium content. On the other hand, it was found that adding niobium leads to a refinement in chromium carbide sizes, directly affecting the hardness of the obtained deposits. There is a direct relationship between the arc energy, with both short and long arc lengths, leading to a tendency to decrease the dilution in the obtained hardfacing.
The aim of this scoping review is to investigate the potential development of an alternative material derived from renewable biological resources such as goldenberry calyx and modified cassava starch as the matrix. Moreover, this paper reviews the impact of combining starch and lignocellulosic fiber on improving the properties of bioplastic materials. The goldenberry calyx is a type of lignocellulosic waste with a low moisture content, which offers logistical advantages, as a high moisture content can accelerate waste deterioration. However, studies on the utilization of goldenberry calyx are scarce. In addition, due to its low cost and availability, starch is the main polysaccharide for biofilm development as a matrix. Combining these two materials can result in a composite material with suitable and adequate properties for packaging applications, although no studies have been published on this specific combination. Starch and lignocellulosic fiber are complementary as the properties of starch biopolymers improve when a hydrophobic material (lignocellulosic fibers) is incorporated. Moreover, starch strengthens fibers by enhancing their biodegradability through its water absorption capacity. In this study, modified cassava starch, with its higher amylose content, is suggested for use, as the proportion of amylose correlates with enhanced bioplastic properties.
In this research, two intermediate layers were deposited on 316L stainless steel to improve the adhesion of diamond-like carbon (DLC) films, one composed of TixAl and produced using the RF sputtering technique with three thicknesses, 100 nm, 200 nm, and 300 nm; the other, interlayer composed of amorphous hydrogenated silicon (a-Si:H). The DLC films were deposited using the pulsed-DC PECVD method with an active screen to achieve the AISI 316L/TixAl//DLC and AISI 316L/TiₓAl/a-Si/DLC configurations. The binding energy between the substrate/TixAl and TixAl/a-Si:H was investigated via X-ray photoelectron spectroscopy with high-resolution spectra. The chemical composition and microstructure of the titanium–aluminum interlayers were investigated using energy-dispersive X-ray spectroscopy and X-ray diffraction, and the microstructure of the DLC coatings was studied using Raman spectroscopy. The coatings’ adherence was measured using scratch and indentation tests, and the hardness of the DLC coatings was determined with the nanoindentation test. The X-ray diffractograms did not allow the determination of any crystalline structure in the TixAl interlayers. The XPS results showed that between the AISI 316L substrate and the TixAl intermediate layer, Ti-O-Fe and FeAl2O4 were formed. On the other hand, at the TixAl/a-Si:H interface, TiSi2 and Al2SiO5 compounds were identified. The DLC coatings grew as hydrogenated amorphous carbon with a hydrogen content of around 30 at.% and a hardness of 24 GPa. The deposition methods used and the TixAl/a-Si:H interlayers allowed the obtainment of adherent DLC coatings on AISI 316L stainless steel substrates. High critical load values of about 30 N were obtained. The novelty of this work is underscored by the absence of previous studies that thoroughly examine the bonds present in interlayers used as gradients to enhance the adhesion of DLC.