Poly(lactic acid) (PLA) is considered the most promising biobased substitute for fossil-derived polymers due to its compostability, biocompatibility, renewability, and good thermomechanical properties. However, PLA suffers from several shortcomings, such as low heat distortion temperature, thermal resistance, and rate of crystallization, whereas some other specific properties, i.e., flame retardancy, anti-UV, antibacterial or barrier properties, antistatic to conductive electrical characteristics, etc., are required by different end-use sectors. The addition of different nanofillers represents an attractive way to develop and enhance the properties of neat PLA. Numerous nanofillers with different architectures and properties have been investigated, with satisfactory achievements, in the design of PLA nanocomposites. This review paper overviews the current advances in the synthetic routes of PLA nanocomposites, the imparted properties of each nano-additive, as well as the numerous applications of PLA nanocomposites in various industrial fields.

Agricultural waste is a renewable source of lignocellulosic components, which can be processed in a variety of ways to yield added-value materials for various applications, e.g., polymer composites. However, most lignocellulosic biomass is incinerated for energy. Typically, agricultural waste is left to decompose in the fields, causing problems such as greenhouse gas release, attracting insects and rodents, and impacting soil fertility. This study aims to valorise nonedible tomato waste with no commercial value in Additive Manufacturing (AM) to create sustainable, cost-effective and added-value PLA composites. Fused Filament Fabrication (FFF) filaments with 5 and 10 wt.% tomato stem powder (TSP) were developed, and 3D-printed specimens were tested. Mechanical testing showed consistent tensile properties with 5% TSP addition, while flexural strength decreased, possibly due to void formation. Dynamic mechanical analysis (DMA) indicated changes in storage modulus and damping factor with TSP addition. Notably, the composites exhibited antioxidant activity, increasing with higher TSP content. These findings underscore the potential of agricultural waste utilization in FFF, offering insights into greener waste management practices and addressing challenges in mechanical performance and material compatibility. This research highlights the viability of integrating agricultural waste into filament-based AM, contributing to sustainable agricultural practices and promoting circular economy initiatives.

Current transdermal drug delivery technologies, like patches and ointments, effectively deliver low molecular weight drugs through the skin. However, delivering larger, hydrophilic drugs and macromolecules remains a challenge. In the present study, we developed novel transdermal nanoneedle patches containing levofloxacin-loaded modified chitosan nanoparticles. Chitosan was chemically modified with transcutol in three ratios (1/1, 1/2, 1/3, w/w), and the optimum ratio was used for nanoparticle fabrication via the ionic gelation method. The successful modification was confirmed using ATR-FTIR spectroscopy, while DLS results revealed that only the 1/3 ratio afforded suitably sized particles of 220 nm. After drug encapsulation, the particle size increased to 435 nm, and the final formulations were examined via XRD and an in vitro dissolution test, which suggested that the nanoparticles reach 60% release in a monophasic pattern at 380 h. We then prepared transdermal patches with pyramidal geometry nanoneedles using different poly(lactic acid)/poly(ethylene adipate) (PLA/PEAd) polymer blends of varying ratios, which were characterized in terms of morphology and mechanical compressive strength. The 90/10 blend exhibited the best mechanical properties and was selected for further testing. Ex vivo permeation studies proved that the nanoneedle patches containing drug-loaded nanoparticles achieved the highest levofloxacin permeation (88.1%).

This research paper highlights the preparation and characterisation of high-density polyethylene (HDPE)/tannic acid (TA) composites, designed to confer antioxidant properties to HDPE, valorising a biobased filler. Indeed, tannic acid is a natural polyphenol, demonstrating, among others, strong antioxidation properties. Using a melt-mixing process, HDPE/TA composites containing various amounts of TA, ranging between 1 and 20 wt%, were prepared, and analyses on their structural, thermal, mechanical, as well as antioxidant properties were conducted. Infrared spectroscopy, differential scanning calorimetry, and X-ray diffraction showed that TA was successfully incorporated into the HDPE matrix. Thermogravimetric analysis evidenced that the onset of thermal degradation decreased, but overall satisfactory stability was observed. The composites exhibited exceptional antioxidant properties, especially the ones with the highest TA content, although it was observed that a high amount of TA had adverse effects on the mechanical performance of the composites.