Using a no-moving-component output-fed bistable fluidic oscillator to control fluid flows into a parallel path has been recognized for a considerable time, but as yet it is not so widely adopted as its obvious benefits would deserve. This may be attributed to the encountered problems associated with its jet behavior, complicated by its loading characteristics. In order to investigate a typical case for the application of the output-fed fluidic oscillator, this paper elaborates on the computational fluid dynamics (CFD) simulation method for studying the performance of a fluidic hammer controlled by an output-fed bistable fluidic oscillator. Given that couple mechanism exists between the flow field in the fluidic oscillator and the impact body, dynamic mesh technique and a user-defined function written in C programming language were used to update the mesh in the simulations. In terms of the evaluation of performance, the focus is on the single-impact energy and output power of the fluidic hammer in this study, to investigate the effect of different parameters of the impact body on them. Experimental tests based on the noncontact measuring method were conducted to verify the simulation results, by which the accuracy and reliability of this CFD simulation method was proved.
Down-the-hole (DTH) hammer drilling with reverse circulation is a novel, mobile, high-speed drilling system suitable for the specific requirements of mine rescue. This technology can be applied to shorten the rescue time during mine accidents. The performance of reverse circulation (RC) drilling depends on the structural design of the drill bit. An orthogonal experimental design is executed to investigate the effect of the structural design parameters of the large-diameter drill bit for drilling rescue wells on the cutting carrying capacity and reverse circulation performance. This study employs computational fluid dynamics (CFD) software to solve the Navier–Stokes equation for three-dimensional steady flow and calculate the flow field around the drill bit to evaluate the RC efficiency. Six key geometric parameters were proven to have a direct influence on the RC performance, including the diameter of suction nozzles Dn, the length of nozzles L, the quantity of nozzles N, the diameter of the pilot hole Dg, the inclination angle of nozzles θs, and the deflection angle of nozzles θd. The CFD simulation experiments were implemented according to the orthogonal array L18(37) and were analyzed using the range, variance, and regression analysis. A mathematical model was developed for the RC efficiency to understand the effect of the factors. The results show that the diameter of suction nozzles Dn has an essential effect on the RC performance of the drill bit. An ideal combination is Dn = 20 mm, L = 50 mm, N = 3, Dg = 50 mm, and θs = 35°, θd = 10°, which was obtained through variance analysis and validated via CFD simulation for higher efficiency. To verify its real performance, a large-diameter RC drill bit with a diameter of 1.2 m was manufactured and tested in the field. The result demonstrated that the drill bit had excellent cutting transport and reverse circulation performance.
A reverse circulation Down-The-Hole (DTH) hammer drill bit in Casing-while-Drilling (CwD) processes is designed and applied to drilling under complicated formation. The drill bit is a special retractable drill bit with an exclusive reverse circulation gas channel. Using numerical simulations and experiments, the influence of the gas channel structure parameters of the drill bit, including the inner jet nozzles, flushing nozzles, suction channel, and other parameters, on its reverse circulation performance is analyzed, and the optimal gas channel structure parameters of the drill bit are determined to improve the reverse circulation effect. The results show that the flushing nozzles and inner jet nozzles have an important influence on entrainment performance. The entrainment rate decreases as the flushing nozzle diameter increases and decreases as the inner jet nozzle diameter increases. An increase in the suction channel diameter can improve the reverse circulation effect of the drill bit. The spiral slot drill bit is more conducive to air being sucked into the central channel in the form of spiral flow, so it can improve the entrainment performance. The entrainment rate can reach 23.4% with the optimum structured drill bit.
The target strata of sandstone-type uranium deposits are usually located in the fragile and loose strata, which makes it difficult to obtain core samples; consequently, a novel ice coring device for loose sandstone-type uranium deposits is proposed to solve this problem. Experiments proved that the artificial sample can replace the natural sample, and the coring method has high reliability. Ensuring the allegro formation of an ice valve with a given cold source is critical for this coring system, and reducing the loss of cold energy with help of insulation layer is one of the methods to speed up the formation of ice valve. Since the diameter of the drill tool is limited by its working scenario, the thickness of insulation layer is limited to ensure the size of core. Therefore, this paper conducted laboratory experiments of the insulation layer with different thicknesses to study the effect of the insulation layer on the formation of the sand–ice valve. Results show that the insulation layer can reduce the loss of cold energy during the freezing process and significantly affect the formation time of the sand–ice valve. When the thickness of the aerogel insulation layer is 2 mm, the freezing time is 44% shorter than that without insulation layer. According to the tests, the novel ice coring device is expected to solve the coring problem in loose sandstone-type uranium deposits.