嘉伟 曲

嘉伟 曲


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 June 2023 in Micromachines
Verified
Journal Article
Open access
PDF file
YLYu Liu
Yu Liu
嘉曲嘉伟 曲
嘉伟 曲
KZKeguang Zhao
Keguang Zhao
XZXuanyuan Zhang
Xuanyuan Zhang
SZShengfang Zhang
Shengfang Zhang
SiCp/Al composites have excellent physical properties and are widely used in aerospace and other fields. Because of their poor machinability, they are often machined by non-traditional machining methods such as electrical discharge machining (EDM). In the process of EDM, due to the “shielding” effect of the reinforced particles of SiC, the local ejection force is low during the processing process, and it is difficult to throw the reinforced particles smoothly, which ultimately leads to a low material removal rate and poor surface quality. In this paper, a high–low-voltage composite ejecting-explosion EDM power supply is developed to explore the explosive effect of reinforced particles in the ejecting-explosion EDM process and the unique process law of the explosion process. The experiment platform uses self-developed CNC machining machine tools based on an ejecting-explosive EDM power supply, and the influence of a detonation-increasing wave on the processing of SiCp/Al composites with different volume fractions was studied by changing four factors: the open-circuit voltage difference, pulse current difference, pulse phase difference, and pulse width difference of the back wave behind the step front. The material removal rate and surface roughness were measured. The research results showed that the material removal rate could be increased to 164.63%, and the material surface roughness could be increased to 30.03% by adjusting the high and low pulse current difference from 1 A to 8 A. When the voltage difference between high and low wave (HLW) pulses increases from 40 V to 120 V, the material removal rate can be increased to 150.39%, and the material surface roughness can be increased to 20.49%. The material removal rate increases with the increase in pulse phase difference and open-circuit voltage difference. With the increase in peak current difference and pulse width difference, the material removal rate becomes faster at first and then slower. The surface roughness of materials increases with the growth of open-circuit voltage difference, peak current difference, pulse width difference, and pulse phase difference.

15 January 2025 in Coatings
Verified
Journal Article
Open access
PDF file
YLYu Liu
Yu Liu
SZShiqi Zhang
Shiqi Zhang
WSWeiqiang Shao
Weiqiang Shao
ZWZiguang Wang
Ziguang Wang
嘉曲嘉伟 曲
嘉伟 曲
SZShengfang Zhang
Shengfang Zhang
Aimed at solving the problems of single control measures in the electro-spark deposition (ESD) process, difficulty controlling the micro-process using heterogeneous materials (for the electrode and matrix), and the unstable quality and reliability of repairs to the deposition layer, a method of magnetic-field-assistance electro-spark deposition (MFESD) was proposed. An MFESD device was built, and a Ni electrode was used for deposition on the surface of 45 steel under the conditions of deposition voltages of 30 V, 60 V, and 90 V, respectively. This study examined the impact of the magnetic field’s intensity and frequency on the microstructure and mechanical properties of electro-spark deposition layers. The results show that the sputtering and protrusion of the electrode material on the surface of the deposition layer gradually decrease with an increase in the magnetic field’s intensity and frequency, defects such as pores and cracks are obviously improved, and the structure is uninterrupted and compact. The surface roughness of the deposited layer decreases with an increase in the magnetic field’s intensity and frequency, and its surface roughness decreases by 44.3%. The cross-section effect of the deposited layer is improved. The thickness of the deposited layer increases with an increase in the magnetic field’s intensity and frequency; the thickness of the deposited layer increases by 13.39%, and its maximum thickness can reach 54.396 μm. At the same time, the microhardness of the deposited layer increases with an increase in the two aforementioned properties of the magnetic field, and its hardness increases by 5.32%. Using a magnetic field to control ESD can effectively control the microscopic process of deposition and obtain high-quality deposition coatings, which have important significance in the surface remanufacturing of key components of high-end equipment.

31 October 2023 in Coatings
Verified
Journal Article
Open access
PDF file
YLYu Liu
Yu Liu
QSQuanning Su
Quanning Su
SZShiqi Zhang
Shiqi Zhang
嘉曲嘉伟 曲
嘉伟 曲
SZShengfang Zhang
Shengfang Zhang
As a surface-strengthening technology, electro-spark deposition (ESD) is widely used in the strengthening and repair of key components of high-end equipment. In this paper, a fusion and solidification model of ESD coating is established. The method of heat–fluid–solid interaction is adopted to simulate the material’s flow and fusion process in the droplet dropping into the molten pool. The distribution law of the coating-matrix material inside the coating was studied. Through the heat transfer between the molten material and the matrix material, the condensation and solidification process of the coating-matrix material is simulated, the temperature change in the coating area during the solidification process is analyzed, and the solidification law of the molten material is studied. The results show that the deposition time reaches 80 μs, and the content of electrode material at the bottom of the molten pool reaches 4.5%. The content of electrode material in the upper region of the material gushing out of the molten pool is higher than that in the bottom region. The material outside the molten pool solidifies first, and the molten material in the molten pool gradually solidifies from the bottom up; the shape of the solidification interface is similar to the boundary of the molten pool. Through the single-point deposition experiment of electro-spark deposition, the surface morphology of the deposition point was observed. The depth of the concave part of the contour can reach 16 μm. The difference between the two contour curves in the horizontal direction is not much; the error of the diameter is about 4%. The element distribution of the surface and the section of the deposition point are analyzed. The diffusion distance in the depth direction of the coating is about 4μm, and the transverse diffusion distance inside the coating is 364 μm. The error is 7.6% compared with the experimental results. The cross-section structure of the deposition point was observed, and the error between the experimental results and the simulation results in diameter is about 11%. It was found that the material distribution in the sedimentary area is basically consistent with the simulation results, and the simulation results are verified from the side.

28 February 2023 in Machines
Verified
Journal Article
Open access
PDF file
YLYu Liu
Yu Liu
嘉曲嘉伟 曲
嘉伟 曲
XCXintong Cai
Xintong Cai
WZWenchao Zhang
Wenchao Zhang
SZShengfang Zhang
Shengfang Zhang
Worn cemented carbide tool bits are often discarded because of the difficulty of their repair, resulting in a great deal of waste. Surface strengthening technology often extends the service life of worn tools. Electro-spark deposition (ESD) coating and matrix materials are metallurgically and closely bonded, and the approach has the characteristics of small heat input, a small heat-affected zone, and low repair cost, so it is suitable for strengthening the surface of cemented carbide tools. As the surface of cemented carbide tools is often not flat, which affects the uniformity of the deposited layer, the surface needs to be polished before ESD. Therefore, this paper proposed a method involving the electro-spark additive and subtractive repair of worn cemented carbide. Experiments involving the ultrasonic-assisted EDM grinding (UEDG) of cemented carbide were carried out. The effect of brass, 45 steel, and tungsten electrode materials on the removal rate, tool wear, and surface roughness were investigated. The results showed that the material removal rate of the tungsten electrode could reach 3.27 mm3/min, while the electrode loss was only 8.16%, and the average surface roughness was only 2.465 μm, which was better than the other two electrodes. Thus, the tungsten electrode exhibited a high material removal rate, low electrode loss, and good surface quality. The effects of the TiC, TiN, and TC4 electrodes on cemented carbide ESD were studied using optical 3D surface topography and other instruments, and the surface roughness, thickness, and hardness of the deposited layer were compared. The results showed that the surface roughness of the TC4 material reached 52.726 μm, which was better than that of the TiN and TiC materials. The thickness of the TiC deposition layer was 172.409 μm and the hardness value was 2231.9 HV; thus, the thickness and hardness of the TiC material’s sedimentary layer were better than those of the TiN and TC4 materials.