The low-voltage ride through (LVRT) requirement demands the wind power plants to remain connected to the grid in the presence of grid voltage dips, actively helping the network overall control to keep network voltage and frequency stable. Wind power technology points to increase power ratings. Hence, multilevel converters, as for example, neutral-point- clamped (NPC) converters, are well suited for this application. Predictive current control presents similar dynamic response and reference tracking than other well-established control methods, but working at lower switching frequencies. In this paper, the predictive current control is applied to the grid-side NPC converter as part of a wind energy conversion system, in order to fulfill the LVRT requirements. DC-link neutral-point balance is also achieved by means of the predictive control algorithm, which considers the redundant switching states of the NPC converter. Simulation and experimental results confirm the validity of the proposed control approach.

Aiming to improve the performance features of conventional two-level dual-active-bridge (DAB) converters, this paper presents a three-level neutral-point-clamped (NPC) DAB dc-dc converter. A general modulation pattern is initially defined, the dc-link capacitor voltage balancing is analyzed in detail, and a proper balancing control is designed. Then, a set of decoupled optimization problems is formulated as a function of the available modulation degrees of freedom to minimize the predominant converter losses. Finally, a simple and practical specific modulation strategy is provided, resembling the optimum solutions. The good performance of the proposed three-level NPC DAB converter operated with the proposed modulation strategy and voltage balancing control is verified through simulation and experiments. The capacitor voltage balancing can be guaranteed for all operating conditions. In addition, it is concluded that the multilevel topology provides benefits compared with the conventional two-level DAB converter.

Thanks to the inherent redundancy to generate the different output voltage levels, the multilevel active-clamped (MAC) topology presents an important fault-tolerance ability which makes it interesting for several applications. This paper presents an analysis of the fault-tolerance capacity of the MAC converter. Both open-circuit and short-circuit faults are considered, and the analysis is carried out under single-device and two simultaneous device faults. Switching strategies and different hardware modifications to overcome the limitations caused by faults are proposed. Experimental tests with a four-level MAC prototype are presented to validate the analysis.

This paper presents a capacitor voltage balancing control applicable to any multilevel dc-ac converter formed by a single set of series-connected capacitors implementing the dc link and semiconductor devices, such as the diode-clamped topology. The control is defined for any number of dc-link voltage levels and converter legs (for single-phase and multiphase systems), guaranteeing the capacitor voltage control for any modulation index value and load (from idle mode to full power). The associated control loop small-signal transfer function is presented, from which optimum compensator design guidelines are derived. The improvement in control performance is verified through simulation and experiments comparing with a previous balancing control strategy in a four-level three-phase dc-ac conversion system. The satisfactory control performance is also verified through simulation in a four-level five-phase dc-ac conversion system.

This paper presents a novel multilevel active-clamped converter topology, which is an extension to m levels of the three-level active neutral-point-clamped topology. The operating principle is established through the definition of a proper set of switching states and a transition strategy between adjacent switching states. The benefits of the proposed converter topology and control in comparison to alternative multilevel converter topologies are discussed. The simulation and experimental results of a simple four-level dc-dc converter configuration are presented to illustrate the converter performance features. The experimental results of a four-level three-phase dc-ac converter are also presented to further validate the proposed topology and operating principle.

Several pulsewidth modulation (PWM) strategies have been proposed for three-phase multilevel converters. Typically, these PWM methods can be either space-vector or carrier-based implemented, where the carrier-based implementation usually presents a lower computation complexity. In this paper, a novel approach for the carrier-based implementation of different existing PWM methods is proposed for three- (3L) and four-level (4L) dc-ac converters, which can be easily extended to any number of levels. The main features of the proposed approach are its reduced computation complexity and computation time. On the other hand, the proposed approach suggests the derivation of novel PWM strategies which can potentially present improved performance features. As an example, two new discontinuous PWM (DPWM) strategies are proposed for the 4L converter. One of these DPWM strategies presents lower weighted total harmonic distortion than other previously proposed strategies. Simulation and experimental results verify the effectiveness of the proposed approach and novel DPWM strategies.