The liquid organic fraction of pyrolytic tar has a high energy value which makes possible its utilization as an energy source. However, before utilization, it is crucial to remove water from the liquid fraction. The presence of water reduces the energy value of pyrolytic tars. Water separation from the organic tar fraction is a complex process, since an emulsion can be readily formed. Therefore, after phase separation, it is important to know the residual water content in the organic phase and whether it is necessary to further dry it. The results presented in this manuscript focus on a water determination in liquid products from coal and biomass pyrolysis by a coulometric Karl‑Fischer titration. The Coulometric Karl‑Fischer titration is often used for a water content determination in gaseous, liquid and solid samples. However, to date, this titration method has not been used for a water determination in tars. A new water determination method, which has been tested on different types of tar, has been developed. The Coulometric Karl‑Fischer titration is suitable for tar samples with a water content not greater than 5 wt. %. The obtained experimental results indicate that the new introduced method can be used with a very good repeatability for a water content determination in tars.
Tars from pyrolysis of brown coal can be refined to obtain compounds suitable for fuel production. However, it is problematic to refine the liquids from brown coal pyrolysis, because high molecular compounds are produced, and the sample solidifies. Therefore we decided to investigate the possibility of treating the product in the gas phase during pyrolysis, using a catalyst. A two-step process was investigated: thermal-catalytic refining. In the first step, alumina was used as the filling material, and in the second step a catalyst based on W-Ni was used. These materials were placed in two separate layers above the coal, so the volatile products passed through the alumina and catalyst layers. Pyrolysis tests showed that using the catalyst has no significant effect on the mass balance, but it improves the properties of the gas and the properties of the organic part of the liquid pyrolysis products, which will then be processed further.
In this study, the sorption capacity of limestone samples for CO2 was investigated to determine the conditions under which they can be used in the high-temperature carbonate loop process. For the work, limestone samples from the Czech Republic were used, which contained a high proportion of CaO (more than 97 wt.%). A total of 20 cycles of calcination (950 °C) and subsequent CO2 sorption–carbonation (650 °C) were performed for each limestone sample tested. The sorption capacity towards CO2 in the 20th cycle was less than 10% of the value determined in the first carbonation cycle of the samples and the most significant decrease was observed between the first and second cycles. The highest sorption capacity was determined for the Branžovy sample, which captured 268 mL of CO2/per 1 g of sorbent by chemisorption. Only 15 mL of carbon dioxide per 1 g of sorbent was bound by physisorption. However, in repeated use, the Vitošov limestone had the highest sorption capacity for CO2. For all samples, the amount of carbon dioxide bound by physisorption was in the range of 4 to 10% of the amount bound by chemisorption. Due to sintering of the material, the BET specific surface area decreased by 95 to 96%.
The methanation of carbon dioxide via its reaction with hydrogen has recently become a widely studied topic. This process is typically investigated in a flow system with a catalyst placed in a catalytic reactor through which a mixture of reactant gases (carbon dioxide and hydrogen) flows. In contrast, this study investigates a batch reactor concept, where carbon dioxide is adsorbed within the porous structure of the catalyst and hydrogen is subsequently introduced. The novelty of this research lies in the technological arrangement of the process, in which a single material simultaneously acts as both adsorbent and catalyst within one reactor, enabling alternating CO2 adsorption and its subsequent methanation. The central component is therefore an adsorbent for carbon dioxide capture that also serves as a catalyst for its conversion into methane. A system based on this principle can therefore be used both for capturing carbon dioxide from various gas mixtures with recovery in purified form and for its conversion into synthetic methane, provided a sufficient supply of hydrogen is available. This research confirms that the investigated single-reactor methanation approach using one material that functions both as adsorbent and catalyst is fully operational and suitable for further testing at the pilot scale.