Veronika Kyselová

Mrs. Veronika Kyselová

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 April 2019 in Energy & Fuels
Verified
Journal Article
Closed access
KCKarel Ciahotný
Karel Ciahotný
VKVeronika Kyselová
Veronika Kyselová

23 May 2024 in Gels
Verified
Journal Article
Open access
PDF file
VKVeronika Kyselová
Veronika Kyselová
JHJakub Havlín
Jakub Havlín
KCKarel Ciahotný
Karel Ciahotný
This work studied the low-temperature sorption of carbon dioxide on impregnated silica gel. An impregnating agent was used polyethyleneimine. The content of the impregnating agent in the silica gel matrix was 33.4 wt.%. Material properties such as the Brunauer–Emmett–Teller (BET) surface area, pore distribution, total pore volume, and thermal stability of the impregnated material were determined for the sample. During the measurement of the adsorption–desorption cycles, the loss of the impregnating agent in the material matrix was also determined. Due to the decrease in the content of polyethyleneimine, the sorption capacity of the adsorbent for CO2 also decreased. It was found that after the 20th adsorption–desorption cycle, the content of the impregnating agent in the adsorbent dropped by 3.15 wt.%, and, as a result, the adsorption capacity for CO2 dropped to almost half.

16 September 2020 in Inorganic Chemistry
Verified
Journal Article
Closed access
LKLibor Kobera
Libor Kobera
JHJakub Havlin
Jakub Havlin
SASabina Abbrent
Sabina Abbrent
JRJan Rohlicek
Jan Rohlicek
MSMagdalena Streckova
Magdalena Streckova
JBJiří Brus
Jiří Brus

24 March 2023 in Crystals
Verified
Journal Article
Open access
PDF file
VKVeronika Kyselová
Veronika Kyselová
LJLenka Jílková
Lenka Jílková
KCKarel Ciahotný
Karel Ciahotný
In this study, the sorption capacity of limestone samples for CO2 was investigated to determine the conditions under which they can be used in the high-temperature carbonate loop process. For the work, limestone samples from the Czech Republic were used, which contained a high proportion of CaO (more than 97 wt.%). A total of 20 cycles of calcination (950 °C) and subsequent CO2 sorption–carbonation (650 °C) were performed for each limestone sample tested. The sorption capacity towards CO2 in the 20th cycle was less than 10% of the value determined in the first carbonation cycle of the samples and the most significant decrease was observed between the first and second cycles. The highest sorption capacity was determined for the Branžovy sample, which captured 268 mL of CO2/per 1 g of sorbent by chemisorption. Only 15 mL of carbon dioxide per 1 g of sorbent was bound by physisorption. However, in repeated use, the Vitošov limestone had the highest sorption capacity for CO2. For all samples, the amount of carbon dioxide bound by physisorption was in the range of 4 to 10% of the amount bound by chemisorption. Due to sintering of the material, the BET specific surface area decreased by 95 to 96%.

30 September 2024 in Paliva
Verified
Journal Article
Open access
MSMarek Staf
Marek Staf
VKVeronika Kyselová
Veronika Kyselová
ALAdam Loos
Adam Loos
The study presented here focused on the research of adsorbents for the separation of carbon dioxide from flue gas or other waste gases. Specifically, it focused on the possibility of eliminating the permanent problem with the insufficient resistance of inorganic adsorbents to unwanted – parasitic – adsorption of moisture from the processed gas. Based on the promising data published in recent papers regarding the wet impregnation of adsorbents with branched polyethyleneimine (PEI), four methods for the preparation of PEI-impregnated zeolite were tested. Penetration of the agent into the porous structure of the zeolite was achieved by: applying ultrasound, applying vacuum, combining vacuum and overpressure and boiling off the solvent without further operation. The raw zeolite was characterized by X-ray fluorescence spectrometry and X-ray diffractometry and also subjected to textural analysis. The characterization of the impregnated products mainly included thermogravimetric analysis, textural analysis and organic elemental analysis. In addition to gravimetric screening, the adsorption capacities of raw zeolite and impregnated products were primarily determined using a pressure flow-through apparatus with a fixed bed adsorber. The experimental conditions were determined to be close to real industrial installations: temperature during adsorption 20 and 40 °C, pressure during adsorption 600 kPa and 15% volume fraction of CO2 in the gas. Desorption was carried out by a combination of thermal desorption at 80 °C and vacuum. By reproducing the impregnation procedures from the literature, a PEI loading in the range of 4.1–23.7% was achieved, which is significantly lower than the literature sources state for the same preparation procedures. The measurement of textural properties verified that, depending on the value of PEI loading, there is a gradual reduction of the specific surface area, the total pore volume and the virtual disappearance of micropores and small mesopores. Specifically, at a PEI loading of 4%, the BET surface area decreased compared to the pristine zeolite from 29.4 to 2.9 m2 g–1 and at the same time the total pore volume decreased from 0.13 to 0.02 cm3 g–1, etc. The measurement of capacities did not confirm almost any of the results published in the literature. Without exception, the adsorption capacity decreased with the amount of PEI introduced into the zeolite particles. E.g. if a gas with 80% relative humidity and a content of 15% CO2 was used at a pressure of 600 kPa and a temperature of 40 °C, the capacity (by mass) decreased due to impregnation from 2.4% (for raw zeolite) to 0.8% for the sample with PEI mass fraction of 19%. Tests using dry gas resulted in even more marked deterioration. Thus, one can only partially agree with the literature data in the sense that humidity slightly compensates the negative effect of PEI on capacity. The effect, where the capacity increases with increasing temperature due to the replacement of physical CO2 adsorption by its chemisorption in the PEI layer, was also not confirmed. For example, for the above sample, humidity and pressure, the capacity was 0.9% at 20 °C. The impregnation procedure based on boiling off the solvent turned out to be completely unusable and, despite repeated rigorous attempts to reproduce it, did not lead to a product with a measurable capacity. The results of the study can be summarized in the following sentence. The problem is not that the experiments did not lead to a positive result, but above all the fundamental discrepancy between the published data and the attempts to reproduce them.

3 November 2026 in Polish Journal of Environmental Studies
Verified
Journal Article
Open access
PDF file
LJLenka Jílková
Lenka Jílková
KCKarel Ciahotný
Karel Ciahotný
THTomáš Hlinčík
Tomáš Hlinčík
VKVeronika Kyselová
Veronika Kyselová
The methanation of carbon dioxide via its reaction with hydrogen has recently become a widely studied topic. This process is typically investigated in a flow system with a catalyst placed in a catalytic reactor through which a mixture of reactant gases (carbon dioxide and hydrogen) flows. In contrast, this study investigates a batch reactor concept, where carbon dioxide is adsorbed within the porous structure of the catalyst and hydrogen is subsequently introduced. The novelty of this research lies in the technological arrangement of the process, in which a single material simultaneously acts as both adsorbent and catalyst within one reactor, enabling alternating CO2 adsorption and its subsequent methanation. The central component is therefore an adsorbent for carbon dioxide capture that also serves as a catalyst for its conversion into methane. A system based on this principle can therefore be used both for capturing carbon dioxide from various gas mixtures with recovery in purified form and for its conversion into synthetic methane, provided a sufficient supply of hydrogen is available. This research confirms that the investigated single-reactor methanation approach using one material that functions both as adsorbent and catalyst is fully operational and suitable for further testing at the pilot scale.