Krishna Mazumder

Ms. Krishna Mazumder

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 April 2023 in Sensors
Verified
Journal Article
Open access
PDF file
KMKrishna Mazumder
Krishna Mazumder
AGAnumoy Ghosh
Anumoy Ghosh
ABAnagha Bhattacharya
Anagha Bhattacharya
Sarosh AhmadSarosh Ahmad
Sarosh Ahmad
Adnan GhaffarAdnan Ghaffar
Adnan Ghaffar
Mousa I HusseinMousa I Hussein
Mousa I Hussein
This paper presents an effective way to design an RFID tag antenna to operate at three different frequencies by incorporating a switching technique. PIN diode has been used to switch the RF frequency because of its good efficiency and simplicity. The conventional dipole-based RFID tag has been improvised with added co-planar ground and PIN diode. The layout of the antenna is designed with a size of 0.083 λ0 × 0.094 λ0 at UHF (80–960) MHz, where λ0 is the free-space wavelength corresponding to the mid-point of the targeted UHF range. The RFID microchip is connected to the modified ground and dipole structures. Bending and meandering techniques on the dipole length help to match the complex chip impedance with the dipole impedance. Additionally, it scales down the total structure of the antenna. Two PIN diodes are placed along the dipole length at appropriate distances with proper biasing. The ON-OFF switching states of the PIN diodes enable the RFID tag antenna to switch over the frequency ranges (840–845) MHz (India), 902–928 MHz (North America), and 950–955 MHz (Japan).

31 March 2025 in Electronics
Verified
Journal Article
Open access
PDF file
KMKrishna Mazumder
Krishna Mazumder
AGAnumoy Ghosh
Anumoy Ghosh
PSPriyanka Singh
Priyanka Singh
SPSamineni Peddakrishna
Samineni Peddakrishna
JKJayendra Kumar
Jayendra Kumar
This paper proposes a standard applications of Radio Frequency Identification (RFID) system to manage vehicles at electronic toll gate system without compromising the vehicle speed. The existing electronic toll gate system has low latency as each car needs to wait in a queue for passing the gate. Installation of reader antenna at each lane makes the system expensive. We propose a two-ray ground model for using minimal reader antenna to define required antenna height and downtilt angle to cover the total gate area. We estimate that reader antenna at a height of 15 m and 45.4° downtilit angle are required for optimal signal reception from the car at a distance of 35–38 m. Modified Pulse Protocol algorithm is suggested for mitigating reader collision and increase throughput and utilization of the system by 14.71% and 15.2% respectively. The probability distribution function of the contention window is modified to triangular function. The M-ary Trimming Q-tree protocol is suggested to resolve the tag collision by trimming the idle nodes from the query tree, which reduces identification time. The total time slot decreases with higher elements, and the total throughput also increases to 98%. The “no-lane” strategy established a fast, efficient and cost effective vehicle toll collection system.

1 January 2025 in International Journal of RF and Microwave Computer-Aided Engineering
Verified
Journal Article
Open access
KMKrishna Mazumder
Krishna Mazumder
AGAnumoy Ghosh
Anumoy Ghosh
Ahmed Al MansurAhmed Al Mansur
Ahmed Al Mansur
Taha Selim UstunTaha Selim Ustun
Taha Selim Ustun
In the existing radio frequency identification (RFID) system, a single reader antenna is used to identify and share data with the tag. In a large complex environment with dense packing of tag users, a single antenna often leads to a collision and delay due to having a limited data rate and poor coverage. To address the current issues, a dual‐sense circularly polarized (CP) quad‐port multi‐input multioutput (MIMO) reader antenna is proposed that provides an opposite sense of rotation at diagonal pairs in this work. It introduces multipath propagation due to spatial diversity to enhance the RFID performance. Orthogonal modes of the proposed single‐element antenna are evaluated using characteristic mode analysis. In the MIMO layout, a pair of U‐shaped microstrip lines and a series of electromagnetic bandgap (EBG) structures are placed at the bottom side of the substrate for isolation improvement and axial ratio enhancement. The dispersion characteristics of the EBG cell justify the bandgap properties over the operating range. It displays an invariable response of a 10 dB impedance bandwidth of 21.3% (0.77–0.954) and a 3 dB axial ratio bandwidth of 18.8% (0.80–0.97) at all ports, covering the entire RFID band. The antenna maintains more than 25 dB isolation over the operating region of any pair of antenna ports, keeping the interelement spacing of 0.02 λ 0 . λ 0 is the free‐space wavelength at the midpoint operating frequency. Envelope correlation coefficient (ECC) lies below 0.0003, and channel capacity loss (CCL) is 0.0001 bits/s/Hz. The key features of the proposed antenna are suitable for a RFID application to read multiple tags in a crowded tag area with low latency.

14 June 2026 in Electromagnetics
Verified
Journal Article
Closed access
KMKrishna Mazumder
Krishna Mazumder
AGAnumoy Ghosh
Anumoy Ghosh