In this article, a compact coplanar waveguide (CPW) technique based ultra-wideband multiple-input-multiple-output (MIMO) antenna is proposed. The design is characterized by a broad impedance bandwidth starting from 3 GHz to 11 GHz. The overall size of the MIMO design is $60\times60$ mm ² ( $1.24\times 1.24\,\,\lambda _{g}^{2}$ @ 3 GHz) with a thickness of 1.6 mm. To make the design ultra-wideband, the proposed MIMO antenna design has four jug-shaped radiating elements. The design is printed on a FR-4 substrate (relative permittivity of $\varepsilon _{r} = 4.4$ and loss tangent of $\mathrm {tan}\delta = 0.025$ ). The polarization diversity phenomenon is realized by placing four antenna elements orthogonally. This arrangement increases the isolation among the MIMO antenna elements. The simulated results of the ultra-wideband MIMO antenna are verified by measured results. The proposed MIMO antenna has a measured diversity gain greater than 9.98, envelope correlation coefficient (ECC) less than 0.02, and good MIMO performance where the isolation is more than −20dB between the elements. The group delay, channel capacity loss (CCL), and the total active reflection coefficient (TARC) multiplexing efficiency and mean effective gain results are also analyzed. The group delay is found to be less than 1.2ns, CCL values calculated to be less than 0.4 bits/sec/Hz, while the TARC is below −10dB for the whole operating spectrum. The proposed design is a perfect candidate for ultra-wideband wireless communication systems and portable devices.

A type of telecommunication technology called an ultra-wideband (UWB) is used to provide a typical solution for short-range wireless communication due to large bandwidth and low power consumption in transmission and reception. Printed monopole antennas are considered as a preferred platform for implementing this technology because of its alluring characteristics such as light weight, low cost, ease of fabrication, integration capability with other systems, etc. Therefore, a compact-sized ultra-wideband (UWB) printed monopole antenna with improved gain and efficiency is presented in this article. Computer simulation technology microwave studio (CSTMWS) software is used to build and analyze the proposed antenna design technique. This broadband printed monopole antenna contains a jug-shaped radiator fed by a coplanar waveguide (CPW) technique. The designed UWB antenna is fabricated on a low-cost FR-4 substrate with relative permittivity of 4.3, loss tangent of 0.025, and a standard height of 1.6 mm, sized at 25 mm × 22 mm × 1.6 mm, suitable for wireless communication system. The designed UWB antenna works with maximum gain (peak gain of 4.1 dB) across the whole UWB spectrum of 3–11 GHz. The results are simulated, measured, and debated in detail. Different parametric studies based on numerical simulations are involved to arrive at the optimal design through monitoring the effects of adding cuts on the performance of the proposed antennas. Therefore, these parametric studies are optimized to achieve maximum antenna bandwidth with relatively best gain. The proposed patch antenna shape is like a jug with a handle that offers greater bandwidth, good gain, higher efficiency, and compact size.

To support various fifth generation (5G) wireless applications, a small, printed bowtie-shaped microstrip antenna with meandered arms is reported in this article. Because it spans the broad legal range, the developed antenna can serve or reject a variety of applications such as wireless fidelity (Wi-Fi), sub-6 GHz, and ultra-wideband (UWB) 5G communications due to its multiband characterization and optimized rejection bands. The antenna is built on an FR-4 substrate and powered via a 50-Ω microstrip feed line linked to the right bowtie’s side. The bowtie’s left side is coupled via a shorting pin to a partial ground at the antenna’s back side. A gradually increasing meandering microstrip line is connected to both sides of the bowtie to enhance the rejection and operating bands. The designed antenna has seven operating frequency bands of (2.43–3.03) GHz, (3.71–4.23) GHz, (4.76–5.38) GHz, (5.83–6.54) GHz, (6.85–7.44) GHz, (7.56–8.01) GHz, and (9.27–13.88) GHz. The simulated scattering parameter S₁₁ reveals six rejection bands with percentage bandwidths of 33.87%, 15.73%, 11.71, 7.63%, 6.99%, and 12.22%, respectively. The maximum gain of the proposed antenna is 4.46 dB. The suggested antenna has been built, and the simulation and measurement results are very similar. The reported antenna is expanded to a four-element design to investigate its MIMO characteristics.

In this article, a compact printed monopole dual-band antenna using artificial magnetic conductor (AMC)-plane with improved gain and broader bandwidth, applicable for off-body internet of things (IoT) devices is presented. The monopole antenna consists of two C-shaped resonators connected through a U-shaped monopole, parasitic elements, discrete ground circular rings and a co-planar waveguide (CPW) feedline. Each artificial magnetic conductor (AMC) unit cell consists of a slotted circular and a square stubs, designed with two zero-crossing phases for improving the radiation characteristics and to achieve the high gain. The overall size of the proposed AMC-backed antenna is 44.4 mm × 44.4 mm × 1.6 mm with electrical dimensions of 0.75λg×0.75λg×0.027λg. This AMC-backed antenna featured measured bandwidths of 9.6% and 12.4% with improved measured gain values of 4.88 dB and 4.73 dB at 2.45 GHz and 5.8 GHz, respectively. The specific absorption rate (SAR) values are analysed and found to be 1.58 W/kg at 2.45 GHz and 0.9 W/kg at 5.8 GHz. Therefore, the proposed AMC-backed antenna is useful for off-body IoT devices operating at 2.45 and 5.8 GHz industrial, scientific, and medical (ISM) band applications.

A printed monopole antenna for millimeter-wave applications in the 5G frequency region is described in this research. As a result, the proposed antenna resonates in three frequency bands that are designated for 5G communication systems, including 28 GHz, 38 GHz, and 60 GHz (V band). For the sake of compactness, the coplanar waveguide (CPW) method is used. The overall size of the proposed tri-band antenna is 4 mm × 3 mm × 0.25 mm. Using a watch strap and human tissue, such as skin, the proposed antenna gives steady results. At 28 GHz, 38 GHz, and 60 GHz, the antenna’s gain is found to be 5.29 dB, 7.47 dB, and 9 dB, respectively. The overall simulated radiation efficiency is found to be 85% over the watch strap. Wearable devices are a great fit for the proposed tri-band antenna. The antenna prototype was built and tested in order to verify its performance. It can be observed that the simulated and measured results are in close contact. According to our comparative research, the proposed antenna is a good choice for smart 5G devices because of its small size and simple structure, as well as its high gain and radiation efficiency.

In this work, a miniaturized and highly sensitive microwave sensor based on a complementary split-ring resonator (CSRR) is proposed for the detection of liquid materials. The modeled sensor was designed based on the CSRR structure with triple rings (TRs) and a curve feed for improved measurement sensitivity. The designed sensor oscillates at a single frequency of 2.5 GHz, which is simulated using an Ansys HFSS simulator. The electromagnetic simulation explains the basis of the mode resonance of all two-port resonators. Five variations of the liquid media under tests (MUTs) are simulated and measured. These liquid MUTs are as follows: without a sample (without a tube), air (empty tube), ethanol, methanol, and distilled water (DI). A detailed sensitivity calculation is performed for the resonance band at 2.5 GHz. The MUTs mechanism is performed with a polypropylene tube (PP). The samples of dielectric material are filled into PP tube channels and loaded into the CSRR center hole; the E-fields around the sensor affect the relationship with the liquid MUTs, resulting in a high Q-factor value. The final sensor has a Q-factor value and sensitivity of 520 and 7.032 (MHz)/ε_r) at 2.5 GHz, respectively. Due to the high sensitivity of the presented sensor for characterizing various liquid penetrations, the sensor is also of interest for accurate estimations of solute concentrations in liquid media. Finally, the relationship between the permittivity and Q-factor value at the resonant frequency is derived and investigated. These given results make the presented resonator ideal for the characterization of liquid materials.