Hg-Ba-Ca-Cu-O films have been grown on CeO2/R-plane sapphire substrates using a two-step process. First, a 200 nm thick Ba-Ca-Cu-(O, F) precursor film was prepared by sequential evaporation, then Hg-Re-Ba-Ca-Cu-O pellets as a source of Hg-vapour were applied using heat treatment. The prepared films were continuous with sufficient adhesion to the substrate and a maximum zero-resistance critical temperature of TC0 = 118 K. The x-ray diffraction measurements of all the prepared films confirmed the Hg-1212 phase as well as the minor Hg-1223 phase in some cases. We found that the best results were obtained at the mercuration temperature of 775 °C and an optimal annealing time within the range 0.5-5 h. The superconducting properties of the films prepared under unsuitable conditions were mostly improved after annealing in oxygen atmosphere. Darker parts of the film exhibited a different surface morphology and the presence of the Hg-1223 phase in plate-like grains.
1 January 1993 in Collection of Czechoslovak Chemical Communications
Compounds of composition Cu(2,5-DHB)2 . 4 H2O (DHB, dihydroxybenoate anion) and Cu(2,Y-DHB)2 . 8 H2O (Y = 4 or 6) were prepared as potential antiinflamatory gents with a view of pharmacological screening. The room-temperature magnetic moments allow to classify all compounds into the group of magnetically diluted copper(II) complexes. According the EPR and electronic spectra, the degree of tetragonal distortion increases passing from Cu(2,6-DHB)2 . 8 H2O (III) through Cu(2,4-DHB)2 . 8 H2O (I) to Cu(2,5-DHB)2 . 4 H2O (II. The complexes differ also in the cooperative ordering in their structures. All tested compounds exhibit higher antiinflamatory activities (on dextran edema) than free carboxylic acids. However, their effects were accompanied with relatively high toxicity. Remarkable results were also achieved on evaluating the antipyretic activity.
TiO2 nanotube layers (TNT) are prepared by electrochemical anodization of Ti foil in an electrolyte composed of ethylene glycol, ammonium fluoride, and water. The surface of TNT is modified by iron using spin-coating of Fe(NO3)3/IPA (isopropyl alcohol) solution of different concentrations (10 µM−100 mM). The as-prepared materials are annealed at 450 °C for 2 h to form crystalline Fe-TNT. The phase identification and surface morphology of the materials are investigated by XRD and SEM/EDX, respectively. The novelty of this work is based on the investigation of different photochemical processes that could occur simultaneously, and it includes mainly photocatalysis and Fenton-based processes since iron is a Fenton-active element and TiO2 is a photocatalyst. To this end, the degradation of caffeine, an organic pollutant, is performed under solar-like radiation at pH = 3 using different systems that are: (i) Fe-TNT material alone; (ii) a radical precursor alone (H2O2 = 1 mM); and (iii) Fe-TNT combined with H2O2. It is worth noting the degradation mechanism of the organic pollutants occurs via advanced oxidation processes where hydroxyl radicals have been identified as the main reactive oxygen species. One of the main goals of this work is to determine the contribution of the different involved photochemical processes (photocatalysis, photo-Fenton, and photolysis) along with the potential synergy between all these processes. To resume, this work provides new insights into the concept of photochemical versatility (using Fe-TNT), which is scarcely described in the literature.
In this study, we introduced the method for the growth of titanium molybdenum oxide (TMO) nanotubes directly from metallic precursor solid state solution and provided their structural and chemical characterization. Precursor films with content of molybdenum from 32 to 82 at% were prepared using co-deposition magnetron sputtering. The optimization of deposition parameters allowed for the growth of a continuous nanotube array with a length up to 700 nm ± 10% by anodic oxidation. Scanning electron microscopy (SEM) combined with energy-dispersive spectroscopy (EDS) revealed nanotube formation with Ti1−xMoxO2 composition, where x can reach the value of 0.5. Scanning transmission electron microscopy combined with EDS (STEM-EDS) confirmed the incorporation of Mo into the TiO2 lattice and uniform elemental distribution across the nanotube at the submicron level. The nanobeam electron diffraction (NBD) and X-ray diffraction analyses (XRD) did not show any notable crystal phase formation for the titanium molybdenum oxide phase.