Agusti Sin

Agusti Sin

Auto-generated profile, based on publicly available information

Agusti Sin

ITT – Friction Technologies, Via Molini 19, 12032, Barge, CN, Italy

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 April 2003 in Physica C: Superconductivity and its Applications
Verified
Journal Article
Closed access
ZSZ. Supardi
Z. Supardi
GDG. Delabouglise
G. Delabouglise
CPC. Peroz
C. Peroz
ASA. Sin
A. Sin
CVCatherine Villard
Catherine Villard
FWF. Weiss
F. Weiss

1 June 2021 in Open Ceramics
Verified
Journal Article
Open access
ECEnrico Casamassa
Enrico Casamassa
GGGiovanna Gautier
Giovanna Gautier
ASAgusti Sin
Agusti Sin
JKJana Kukutschova
Jana Kukutschova
Maria Giulia FagaMaria Giulia Faga
Maria Giulia Faga

25 September 2001 in Superconductor Science and Technology
Verified
Journal Article
Closed access
PDF file
SCS Chromik
S Chromik
ASA Sin
A Sin
VSV Strbík
V Strbík
GGGustav Gustav
Gustav Gustav
POP Odier
P Odier
FWF Weiss
F Weiss
Hg-Ba-Ca-Cu-O films have been grown on CeO2/R-plane sapphire substrates using a two-step process. First, a 200 nm thick Ba-Ca-Cu-(O, F) precursor film was prepared by sequential evaporation, then Hg-Re-Ba-Ca-Cu-O pellets as a source of Hg-vapour were applied using heat treatment. The prepared films were continuous with sufficient adhesion to the substrate and a maximum zero-resistance critical temperature of TC0 = 118 K. The x-ray diffraction measurements of all the prepared films confirmed the Hg-1212 phase as well as the minor Hg-1223 phase in some cases. We found that the best results were obtained at the mercuration temperature of 775 °C and an optimal annealing time within the range 0.5-5 h. The superconducting properties of the films prepared under unsuitable conditions were mostly improved after annealing in oxygen atmosphere. Darker parts of the film exhibited a different surface morphology and the presence of the Hg-1223 phase in plate-like grains.

1 November 2001 in Journal of Solid State Chemistry
Verified
Journal Article
Closed access
ASA. Sin
A. Sin
FAF. Alsina
F. Alsina
Narcís MestresNarcís Mestres
Narcís Mestres
ASA. Sulpice
A. Sulpice
POP. Odier
P. Odier
MNM. Núñez-Regueiro
M. Núñez-Regueiro

11 April 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
ADAleandro Diana
Aleandro Diana
SCSilvia Comis
Silvia Comis
Paolo InaudiPaolo Inaudi
Paolo Inaudi
SBStefano Bertinetti
Stefano Bertinetti
MTMinghui Tu
Minghui Tu
UOUlf Olofsson
Ulf Olofsson
Here we propose a screening framework that couples controlled pin-on-disc tribology with multi-element PM10 fingerprinting to benchmark brake material pairs. Industrially inspired pad materials representing one non-asbestos organic (NAO) and two low-steel (LS) classes were produced and tested against grey cast iron (GCI) disc and three coated discs. Friction, pin and disc wear, and particle number/mass size distributions were monitored in a closed Pin on Disc chamber using FMPS and ELPI+, while PM10 was collected on PTFE filters. A microwave-assisted digestion protocol (HNO₃/H₂O₂/HBF₄) was validated using SRM NIST 1648a enabling ICP-OES/ICP-MS determination of 29 elements in the collected PM10. The inorganic chemical composition of emitted PM10 was analysed to compare it with the starting friction materials composition. Chemical analysis allowed a comparison of different tribological pairs by evaluating tribological performance, wear, and the existence of correlations between the chemical composition of the PM10 emitted and the starting materials (disc and pad). FESEM analysis coupled with EDX provided morphological and chemical characterisation. Overall, the study shows that simplified formulations, combined with validated multi-element PM10 analysis, offer a practical route to screen disc coatings and pad ingredients and guide materials selection under controlled sliding conditions aiming to address the future development of brake material formulations optimized for performance, durability, and minimal environmental impact.