The electrical properties, resistive switching behavior, and long-term potentiation/depression (LTP/LTD) in a single indium-gallium-zinc-oxide (IGZO) and bi-layer IGZO/ZnO (ZnO: zinc oxide) memristors were investigated for synapse application. The use of the oxide bi-layer memristors, in particular, improved electrical properties such as stability, memristor reliability, and an increase in synaptic weight states. The set voltage of bi-layer IGZO/ZnO memristors was 0.9 V, and the reset voltage was around − 0.7 V, resulting in a low-operating voltage for neuromorphic systems. The oxygen vacancies in the X-ray photoelectron spectroscopy analysis played a role in the modulation of the high-resistance state (HRS) (oxygen-deficient) and the low-resistance state (oxygen-rich) region. The VRESET of the bi-layer IGZO/ZnO memristors was lower than that of a single IGZO, which implied that oxygen-vacancy filaments could be easily ruptured due to the higher oxygen vacancy peak HRS layer. The nonlinearity of the LTP and LTD characteristics in a bi-layer IGZO/ZnO memristor was 6.77% and 11.49%, respectively, compared to those of 20.03% and 51.1% in a single IGZO memristor, respectively. Therefore, the extra ZnO layer in the bi-layer memristor with IGZO was potentially significant and essential to achieve a small set voltage and a reset voltage, and the switching behavior to form the conductive path.
We presented an explicit empirical model of the thermal resistance of AlGaN/GaN high-electron-mobility transistors on three distinct substrates, including sapphire, SiC, and Si. This model considered both a linear and non-linear thermal resistance model of AlGaN/GaN HEMT, the thickness of the host substrate layers, and the gate length and width. The non-linear nature of channel temperature—visible at the high-power dissipation stage—along with linear dependency, was constructed within a single equation. Comparisons with the channel temperature measurement procedure (DC) and charge-control-based device modeling were performed to verify the model’s validity, and the results were in favorable agreement with the observed model data, with only a 1.5% error rate compared to the measurement data. An agile expression for the channel temperature is also important for designing power devices and monolithic microwave integrated circuits. The suggested approach provides several techniques for investigation that could otherwise be impractical or unattainable when utilizing time-consuming numerical simulations.
Schematic illustration of the transition mechanism during the conductive filamentary formation in bilayer HfO 2 /ZnO synaptic devices (a) without and (b) with thermal annealing.
This paper presents a novel approach to the efficient extraction of parasitic resistances in high electron mobility transistors (HEMTs). The study reveals that the gate resistance value can be accurately determined under specific forward gate bias conditions (Vg = 1.0 V), although the gate resistance value becomes unreliable beyond this threshold (Vg > 1.0 V) due to potential damage to the Schottky contact. Furthermore, by examining the characteristics of the device under a cold-FET bias condition (Vds = 0 V), a linear correlation between the gate and drain current is identified, enabling an estimation of the interdependence between the drain and source resistance using the proposed method. The estimation of parasitic pad capacitance (Cpg and Cpd) from Dambrine’s model is refined by incorporating the depletion layer capacitance on the gate side during the pinch-off condition. To validate the accuracy of the extracted parasitic capacitance and resistance values obtained from the new method, small-signal modeling is performed on a diverse range of measured devices.
In this study, we present a detailed analysis of trapping characteristics at the AlxGa1−xN/GaN interface of AlxGa1−xN/GaN high-electron-mobility transistors (HEMTs) with reliability assessments, demonstrating how the composition of the Al in the AlxGa1−xN barrier impacts the performance of the device. Reliability instability assessment in two different AlxGa1−xN/GaN HEMTs [x = 0.25, 0.45] using a single-pulse ID–VD characterization technique revealed higher drain-current degradation (∆ID) with pulse time for Al0.45Ga0.55N/GaN devices which correlates to the fast-transient charge-trapping in the defect sites near the interface of AlxGa1−xN/GaN. Constant voltage stress (CVS) measurement was used to analyze the charge-trapping phenomena of the channel carriers for long-term reliability testing. Al0.45Ga0.55N/GaN devices exhibited higher-threshold voltage shifting (∆VT) caused by stress electric fields, verifying the interfacial deterioration phenomenon. Defect sites near the interface of the AlGaN barrier responded to the stress electric fields and captured channel electrons—resulting in these charging effects that could be partially reversed using recovery voltages. The quantitative extraction of volume trap density (Nt) using 1/f low-frequency noise characterizations unveiled a 40% reduced Nt for the Al0.25Ga0.75N/GaN device, further verifying the higher trapping phenomena in the Al0.45Ga0.55N barrier caused by the rougher Al0.45Ga0.55N/GaN interface.
Tunneling field-effect transistors (TFETs) are a promising candidate for the next generation of low-power devices, but their performance is very sensitive to traps near the tunneling junction. This study investigated the effects of high-pressure deuterium (D2) annealing and hydrogen (H2) annealing on the electrical performance and low-frequency noise (LFN) of a fully depleted silicon-on-insulator p-type TFET. Without high-pressure annealing, the typical noise power spectral density exhibited two Lorentzian spectra that were affected by fast and slow trap sites. With high-pressure annealing, the interface trap density related to fast trap sites was reduced. The passivation of traps near the tunneling junction indicates that high-pressure H2 and D2 annealing improves the electrical performance and LFN properties, and it may become a significant and necessary step for realizing integrated TFET technology in the future.