This study focuses on techno-economic and environmental feasibility study of a hybrid grid connected wind/PV/biomass energy system for Marmara University Goztepe Campus in Istanbul. HOMER software is used to determine the optimum size of the equipment, based on the geographical and meteorological data of the campus. According to the simulation results, the energy system with the minimum net present cost (NPC) and cost of energy (COE) is chosen as the optimum system. Besides, this study aims to reduce greenhouse gas emissions, polluting the air by using renewable resources. Because of negative impacts of the fossil fuels on human health and environment, all the energy sources for this system are renewable energies which have less pollution. In the simulation, PV, wind, and biomass energy resources are used, but the optimum hybrid energy system is determined as grid connected wind/biomass system consisting of 1000 kW grid, 1000 kW biomass generator, and 1500 kW wind turbine. The NPC of the optimum system is calculated as $5.612.501 while the COE is 0,067$/kW. The system also decreases the emissions of greenhouse gases.
30 October 2019 in Balkan Journal of Electrical and Computer Engineering
In this study, Hybrid Renewable Power System (HRPS) has been designed to meet the energy requirement of Istanbul Gedik University Vocational School (IGUVS) in an optimum way. The energy requirement will be achieved mainly with wind and solar power generation system. The hybrid regenerative power system will be requested from the network when it can’t meet its energy needs. The optimum configuration of grid-connected solar/wind hybrid power generation system will be determined by considering the wind speed data and solar radiation data of the location of IGUVS. Moreover, sensitivity analysis will be carried out taking into consideration the wind speed and solar radiation values. If the optimum hybrid power generation system specified is used, the carbon emission values obtained will be examined.
Electric Vehicles (EVs) are rapidly becoming the forerunners of vehicle technology. First electric vehicles were overlooked because of not having adequate battery capacity and because of low efficiency of their electric motors. Developing semiconductor and battery technologies increased the interest in the EVs. Nevertheless, current batteries still have insufficient capacity. As a result of this, vehicles must be recharged at short distances (approximately 150 km). Due to scheduled departure and arrival times EVs appear to be more suitable for city buses rather than regular automobiles. Thanks to correct charging technology and the availability of renewable energy for electric buses, the cities have less noise and CO2 emissions. The energy consumption of internal combustion engines is higher than of the electric motors. In this paper, studies on the commercial electric vehicle charging methods will be reviewed and the plug-in charging processes will be described in detail. This study strives to answer the questions of how plug-in charging process communication has performed between the EV and Electric Vehicle Supply Equipment (EVSE).
25 September 2020 in IEEE Transactions on Power Delivery
The Technology development and rising standards of living are increasing the demand for electricity in city centres. In addition, the density of electric power in different areas of a city changes with the construction of new residential areas. Variation in load density can be managed by adjusting the voltage on distribution lines, installing new lines and transformer centres, and reconfiguring existing lines and transformer centres. In this study, the Istanbul Uskudar District of Kanlica-Cubuklu Region was examined and coverage areas were modified depending on the load density and power of the existing transformers. A novel systematic approach to determine the coverage area of transformers is presented. In this approach, the coverage area and overlap of each transformer with its neighbours were determined. Subsequently, transformers that are under-used or have significant overlap with neighbouring transformers were removed from the network. The transformers were placed into an optimal structure in the network by distributing the load of an excluded transformer to its nearest neighbours. This approach further allows the minimum route for the high voltage distribution wiring between transformers and cost to be determined.
Road lighting constitutes the most important part of city lighting. While correct road lighting solves the chaos in transportation, it also paves the way for smooth urban traffic flow. It also allows people to have a comfortable and safe journey. In order to reduce accidents in the evening hours, safe driving and visual comfort must be provided to drivers. Just like inadequate road lighting, excessive lighting also causes accidents and waste of electrical energy. Good visibility of objects on the road and visual comfort for drivers is possible by ensuring an equal brightness distribution on the road surface. In this article, a prediction model was created with Artificial Neural Network (ANN) and Fuzzy Logic (FL) methods to find the luminance values of the road in Sakıp Sabancı street in Kocaeli province. When the predictions obtained by ANN and FL were compared, the results were seen to be accurate and compatible. When the estimation results obtained as a result of the application were examined, it was observed that the estimation of luminance values in good and qualified road lighting could be achieved with these methods.
1 July 2019 in Tehnicki vjesnik - Technical Gazette
Presented in this study is a principal component analysis - artificial neural network based hybrid failure determination system that can make failure determination selectively and rapidly in asymmetrical external failures that might...