Zhao Mingzhi

Dr. Zhao Mingzhi


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 December 2023 in Energies
Verified
Journal Article
Open access
PDF file
YLyuanyuan Li
yuanyuan Li
XXXu Xiaoyu
Xu Xiaoyu
DBDaorina Bao
Daorina Bao
BRBakhramzhan Rasakhodzhaev Rasakhodzhaev
Bakhramzhan Rasakhodzhaev Rasakhodzhaev
AJAkhadov Jobir
Akhadov Jobir
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
Solar hydrogen production technology is a key technology for building a clean, low-carbon, safe, and efficient energy system. At present, the intermittency and volatility of renewable energy have caused a lot of “wind and light”. By combining renewable energy with electrolytic water technology to produce high-purity hydrogen and oxygen, which can be converted into electricity, the utilization rate of renewable energy can be effectively improved, while helping to improve the solar hydrogen production system. This paper summarizes and analyzes the research status and development direction of solar hydrogen production technology from three aspects. Energy supply mode: the role of solar PV systems and PT systems in this technology is analyzed. System control: the key technology and system structure of different types of electrolytic cells are introduced in detail. System economy: the economy and improvement measures of electrolytic cells are analyzed from the perspectives of cost, consumption, efficiency, and durability. Finally, the development prospects of solar hydrogen production systems in China are summarized and anticipated. This article reviews the current research status of photovoltaic-photothermal coupled electrolysis cell systems, fills the current research gap, and provides theoretical reference for the further development of solar hydrogen production systems.

4 December 2023 in Energies
Verified
Journal Article
Open access
PDF file
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
1Y1 Yu
1 Yu
Chun ChangChun Chang
Chun Chang
DBDaorina Bao
Daorina Bao
AMAohan Mei
Aohan Mei
NWNingbo Wang
Ningbo Wang
Photovoltaic power generation is rapidly developing as a kind of renewable energy that can protect the ecological environment. The establishment of photovoltaic power stations in desertification areas can play a very important role in desert windbreaks and sand fixation as well as improve the ecological environment. The realization of the effective integration of photovoltaics and deserts can have multiple benefits for the economy, society, and ecology. However, the deposition of sand and dust caused by environmental factors in desertification areas can seriously affect the power generation efficiency of PV modules. In this study, the output characteristics of photovoltaic modules were tested under three wind speed conditions (5 m/s, 10 m/s, and 15 m/s), with different sand densities, sand particle sizes, and inclination angles. The experimental study showed that the module’s output power gradually decreased with an increase in the density of accumulated sand; the sand accumulation density on the surface of the photovoltaic module increased from 0 to 40 g/m2, and the maximum output power decreased by 32.2%. As the sand particle size increased, the maximum output power of the module rose and was gradually stabilized in the three wind speed groups. As the sand particle size increased, the maximum output power of the module increased and gradually stabilized in the three wind speed groups. When the wind speed was 15 m/s, the component output power of the angle had the largest drop; the tilt angle was 60° when the relative output power rate reached the minimum (i.e., 86.5%); that is, there was electrical energy loss of approximately 13.7%. The sand particle size and accumulated sand density were the control variables related to the module temperature and the transmittance of the proportion of the impact of the module filling factor differences. According to the curve analysis of the filling factor in different sand accumulation densities, the filling factor first increased and then decreased. In this test, the filling factor at the sand accumulation density of 35 g/m2 (module temperature valley) reached the peak value. The change trend for the component filling factor under different sand particle sizes fluctuated.

20 July 2023 in Energies
Verified
Journal Article
Open access
PDF file
XXXu Xiaoyu
Xu Xiaoyu
Chun ChangChun Chang
Chun Chang
鑫郭鑫 鑫 郭
鑫 鑫 郭
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
The coiled ice-storage-based air conditioning system plays a significant role in enhancing grid peak regulation and improving cooling economy. This paper presents theoretical and experimental studies conducted on the ice storage process of coiled ice storage air conditioning technology. The cooling of water is divided into two stages:10.0 °C to 4.0 °C and 4.0 °C to below 0.0 °C. Initially, the ice storage process forms an ice layer with a thickness of 2.50 mm on the lower surface of the coil, but eventually, the ice layer on the upper surface becomes 3.85 mm thicker than the lower surface as a result of the natural convection of water and density reversal at 4.0 °C. Furthermore, the impact of three coils with different thermal conductivity on the ice storage process was evaluated. It was observed that the thermal conductivity of R-HDPE (reinforced high-density polyethylene) was only 2.6 W/(m·K) higher than HDPE (high-density polyethylene), yet it reduced the freezing time by 34.85%, while the thermal conductivity of steel was 37.4 W/(m·K) higher than R-HDPE, but only decreased the freezing time by 9.40%. The results demonstrated that the rate of ice accumulation increased with thermal conductivity. However, when the coil material’s thermal conductivity surpassed that of ice, the further increase of thermal conductivity gradually weakened its impact on the ice storage rate.

31 January 2024 in Energies
Verified
Journal Article
Open access
PDF file
XLxin liu
xin liu
NWNingbo Wang
Ningbo Wang
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
XHXiaoming Hu
Xiaoming Hu
Photovoltaic power generation is one of the most effective measures to reduce greenhouse gas emissions, and the surface of photovoltaic modules in desert areas is mainly affected by sand erosion and cover, which affect power output. Therefore, a wind–sand erosion system was established to simulate the desert wind–sand environment, analyze the influence of dust erosion on the output power of the component, and observe the surface erosion morphology of the component. Then, dust particles of different sizes were selected to cover the surface of the photovoltaic module, and the temperature change and output characteristics of the backplane of the module were studied. The results show that the erosion rate increases with the increase in the erosion angle. When the erosion rate is 25 m/s and 30 m/s, the output power decreases by 9.82%~16.00% and 15.42%~24.46% at different erosion angles, respectively. As the particle size (0.05 mm~0.30 mm) deposited on the surface of the photovoltaic module gradually increases, the open-circuit voltage of the module changes little, and its maximum difference is 0.25 V. Short-circuit current and output power vary greatly; the maximum difference in short-circuit current is about 13.00%, and the maximum difference in output power is about 17.00%. Through our research, this study provides a certain reference for maximizing power generation efficiency and the clean planning of desert photovoltaic power stations.

7 November 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
RYRong Yu
Rong Yu
Chun ChangChun Chang
Chun Chang
DBDaorina Bao
Daorina Bao
AMAohan Mei
Aohan Mei
NWNingbo Wang
Ningbo Wang
In the natural environment, sand accumulation and desertification can influence the efficiency of photovoltaic arrays. In this study, PV module output characteristics were examined under different sand particle size, varying sand densities and inclination angles, and at wind speeds of 5m/s, 10m/s, and 15m/s. Both theoretical and experimental results showed that the output power of the module declines with increasing sand density. As the sand particle size increases, the module maximum output power rises and then stabilizes. The two control variables, namely sand density and sand particle size, influence the module temperature and light transmittance distinctly. Contrary to the impact of sand density on the module filling factor curve, the module filling factor exhibits varying trends under different sand particle sizes. Additionally, the pattern of the module filling factor as a function of sand density contrasts with that of the module temperature under analogous conditions. Specifically, when the sand density on the PV module surface increases from 0 to 40g/m², there is a 32.2% reduction in maximum output power. At a wind speed of 15m/s, this reduction was found consistent across all wind speed categories. Furthermore, the trend of the module filling factor rel-ative to sand accumulation density contrasts with the module temperature trend under analogous conditions. Notably, the filling factor reached its apex at a sand accumulation density of 35g/m², which corresponded to the module temperature's nadir during the experiment.

2 July 2023 in Energies
Verified
Journal Article
Open access
PDF file
Zhao MingzhiZhao Mingzhi
Zhao Mingzhi
NWNingbo Wang
Ningbo Wang
Chun ChangChun Chang
Chun Chang
XHXiaoming Hu
Xiaoming Hu
YLYingjie Liu
Yingjie Liu
JWJianan Wang
Jianan Wang
The greenhouse’s energy consumption is a major limiting factor for output and development. To address this, it is necessary to adopt green and low-carbon heating technologies to replace traditional fuels. This will not only help conserve energy but will also reduce emissions, thereby improving the thermal environmental conditions for agriculture. This paper aims to research and develop a vertical heat exchange tube array device specifically designed for greenhouses. The focus is on enhancing the passive heat absorption and heat storage efficiency of the device and its influence on the thermal environment of the greenhouse. In order to improve the heat absorption and storage efficiency of the heat exchanger device and its impact on the greenhouse thermal environment, experimental comparative analysis was conducted using air, water, and phase-change materials as working fluids inside the pipes. Through a combination of experiments and simulations, it was verified that the heat exchanger device is capable of actively regulating the greenhouse thermal environment. The results show that heat exchangers of all three types of working fluids can effectively improve the stability of soil temperature and play a “shifting the peak and filling the valley” role in regulating the indoor air temperature while positively regulating the relative humidity of the air. Notably, when the working fluid is a phase-change material, it has the most significant impact on the thermal environment of the greenhouse.