Photovoltaic power generation is rapidly developing as a kind of renewable energy that can protect the ecological environment. The establishment of photovoltaic power stations in desertification areas can play a very important role in desert windbreaks and sand fixation as well as improve the ecological environment. The realization of the effective integration of photovoltaics and deserts can have multiple benefits for the economy, society, and ecology. However, the deposition of sand and dust caused by environmental factors in desertification areas can seriously affect the power generation efficiency of PV modules. In this study, the output characteristics of photovoltaic modules were tested under three wind speed conditions (5 m/s, 10 m/s, and 15 m/s), with different sand densities, sand particle sizes, and inclination angles. The experimental study showed that the module’s output power gradually decreased with an increase in the density of accumulated sand; the sand accumulation density on the surface of the photovoltaic module increased from 0 to 40 g/m2, and the maximum output power decreased by 32.2%. As the sand particle size increased, the maximum output power of the module rose and was gradually stabilized in the three wind speed groups. As the sand particle size increased, the maximum output power of the module increased and gradually stabilized in the three wind speed groups. When the wind speed was 15 m/s, the component output power of the angle had the largest drop; the tilt angle was 60° when the relative output power rate reached the minimum (i.e., 86.5%); that is, there was electrical energy loss of approximately 13.7%. The sand particle size and accumulated sand density were the control variables related to the module temperature and the transmittance of the proportion of the impact of the module filling factor differences. According to the curve analysis of the filling factor in different sand accumulation densities, the filling factor first increased and then decreased. In this test, the filling factor at the sand accumulation density of 35 g/m2 (module temperature valley) reached the peak value. The change trend for the component filling factor under different sand particle sizes fluctuated.
Photovoltaic power generation is one of the most effective measures to reduce greenhouse gas emissions, and the surface of photovoltaic modules in desert areas is mainly affected by sand erosion and cover, which affect power output. Therefore, a wind–sand erosion system was established to simulate the desert wind–sand environment, analyze the influence of dust erosion on the output power of the component, and observe the surface erosion morphology of the component. Then, dust particles of different sizes were selected to cover the surface of the photovoltaic module, and the temperature change and output characteristics of the backplane of the module were studied. The results show that the erosion rate increases with the increase in the erosion angle. When the erosion rate is 25 m/s and 30 m/s, the output power decreases by 9.82%~16.00% and 15.42%~24.46% at different erosion angles, respectively. As the particle size (0.05 mm~0.30 mm) deposited on the surface of the photovoltaic module gradually increases, the open-circuit voltage of the module changes little, and its maximum difference is 0.25 V. Short-circuit current and output power vary greatly; the maximum difference in short-circuit current is about 13.00%, and the maximum difference in output power is about 17.00%. Through our research, this study provides a certain reference for maximizing power generation efficiency and the clean planning of desert photovoltaic power stations.
In the natural environment, sand accumulation and desertification can influence the efficiency of photovoltaic arrays. In this study, PV module output characteristics were examined under different sand particle size, varying sand densities and inclination angles, and at wind speeds of 5m/s, 10m/s, and 15m/s. Both theoretical and experimental results showed that the output power of the module declines with increasing sand density. As the sand particle size increases, the module maximum output power rises and then stabilizes. The two control variables, namely sand density and sand particle size, influence the module temperature and light transmittance distinctly. Contrary to the impact of sand density on the module filling factor curve, the module filling factor exhibits varying trends under different sand particle sizes. Additionally, the pattern of the module filling factor as a function of sand density contrasts with that of the module temperature under analogous conditions. Specifically, when the sand density on the PV module surface increases from 0 to 40g/m², there is a 32.2% reduction in maximum output power. At a wind speed of 15m/s, this reduction was found consistent across all wind speed categories. Furthermore, the trend of the module filling factor rel-ative to sand accumulation density contrasts with the module temperature trend under analogous conditions. Notably, the filling factor reached its apex at a sand accumulation density of 35g/m², which corresponded to the module temperature's nadir during the experiment.
The stratum and microenvironment temperatures in a greenhouse are important factors that affect crop yield. In order to solve the problem of temperature imbalance caused by solar radiation in greenhouses, this paper proposes the application of a solar radiation array tube in a greenhouse. By adding water or phase change materials to the array tube, the influence of the array tube on the formation and microenvironment temperature changes was studied, and a 10-day test was carried out. A test group and control group were set up to monitor test results, and the ground was divided into six areas. The depths of each area were 10 cm, 30 cm, and 50 cm, and the heights of the greenhouse centers were 0 cm, 30 cm, 60 cm, 90 cm, 120 cm, 150 cm, and 180 cm. Via an analysis of the test results obtained for the formation and microenvironment temperature, the arrangement of the array tube was found to exert a constant temperature regulation effect on the microenvironment of the greenhouse at a formation depth of 10 cm and was able to improve this formation depth to a certain extent. The temperature at 30 cm and 50 cm plays a positive role in building a good vegetation growth environment.