This review summarizes the epitaxial growth of crystal phase quantum dots in nanowires in terms of basic concepts, control of the crystal phase in the axial direction, shell growth in the radial direction and optical and electronic properties.
Surface acoustic wave (SAW) resonators have been fabricated on a 2 μ m scandium aluminium nitride (ScAlN) film deposited by means of pulsed-DC reactive magnetron sputtering on a 5.8 μ m polycrystalline diamond substrate. Thin film characterization comprised of the assessment of the thin film texture by means of x-ray diffraction (XRD) measurements, reporting highly c -axis oriented ScAlN thin films with a full width at half maximum (FWHM) of the ω - θ scans below 2°. Compositional and piezoelectric analyses of the thin films synthesized with the sputtering parameters used in this work, namely a sputtering power of 700 W and a synthesis pressure of 0.53 Pa, have reported a thin film composition of Sc 0.26 Al 0.74 N together with a piezoelectric d 33 constant of −11 pC/N. Finally, a SAW resonator has been characterized using a vector network analyser (VNA) under various substrate temperature conditions with two iterations. The resulting temperature coefficient of frequency (TCF) values show a highly linear behaviour within two temperature ranges, namely from 20 K to room temperature (300 K) (−12.5 ppm/K) as well as from 300 K up to 450 K (−34.6 ppm/K).
The massive data transfer rates of nowadays mobile communication technologies demand devices not only with outstanding electric performances but with example stability in a wide range of conditions. Surface acoustic wave (SAW) devices provide a high Q-factor and properties inherent to the employed materials: thermal and chemical stability or low propagation losses. SAW resonators and filters based on synthetized by reactive magnetron sputtering on single crystal and polycrystalline diamond substrates were fabricated and evaluated. Our SAW resonators showed high electromechanical coupling coefficients for Rayleigh and Sezawa modes, propagating at 1.2 GHz and 2.3 GHz, respectively. Finally, SAW filters were fabricated on /diamond heterostructures, with working frequencies above 4.7 GHz and ~200 MHz bandwidths, confirming that these devices are promising candidates in developing 5G technology.
Surface Acoustic Waves (SAW) are one of the possible solutions to target the challenges faced by modern spintronic devices. The stress carried by the SAW can decrease the current required to achieve magnetic switching or domain wall movement by spin transfer torque. Although the last decade has produced very relevant results in this field, it is still important to study the effects of a SAW on the basic unit of many spintronic devices, a ferromagnetic nanostrip. In this work, we perform a complete set of measurements and simulations to characterize the magnetization process of a Ni nanostrip under the influence of a SAW. We find that the SAW increases the mobility and the depinning ability of the magnetic domain walls and consequently, promotes a sharper approach to saturation and substantially decreases coercivity. We have also found other two interesting effects. When the SAW has sufficient energy, is able to trigger irreversible transitions even before switching the direction of the external magnetic field. Additionally, we have found that the magnetization process depends on the direction of the travelling SAW.
In this work, we study the influence of the different surface terminations of c-plane sapphire substrates on the synthesis of graphene via plasma-enhanced chemical vapor deposition. The different terminations of the sapphire surface are controlled by a plasma process. A design of experiments procedure was carried out to evaluate the major effects governing the plasma process of four different parameters: i.e., discharge power, time, pressure and gas employed. In the characterization of the substrate, two sapphire surface terminations were identified and characterized by means of contact angle measurements, being a hydrophilic (hydrophobic) surface and the fingerprint of an Al- (OH-) terminated surface, respectively. The defects within the synthesized graphene were analyzed by Raman spectroscopy. Notably, we found that the ID/IG ratio decreases for graphene grown on OH-terminated surfaces. Furthermore, two different regimes related to the nature of graphene defects were identified and, depending on the sapphire terminated surface, are bound either to vacancy or boundary-like defects. Finally, studying the density of defects and the crystallite area, as well as their relationship with the sapphire surface termination, paves the way for increasing the crystallinity of the synthesized graphene.