The article presents the potential application of the time domain reflectometry (TDR) technique to measure moisture transport in unsaturated porous materials. The research of the capillary uptake phenomenon in a sample of autoclaved aerated concrete (AAC) was conducted using a TDR sensor with the modified construction for non-invasive testing. In the paper the basic principles of the TDR method as a technique applied in metrology, and its potential for measurement of moisture in porous materials, including soils and porous building materials are presented. The second part of the article presents the experiment of capillary rise process in the AAC sample. Application of the custom sensor required its individual calibration, thus a unique model of regression between the readouts of apparent permittivity of the tested material and its moisture was developed. During the experiment moisture content was monitored in the sample exposed to water influence. Monitoring was conducted using the modified TDR sensor. The process was additionally measured using the standard frequency domain (FD) capacitive sensor in order to compare the readouts with traditional techniques of moisture detection. The uncertainty for testing AAC moisture, was expressed as RMSE (0.013 cm³/cm³) and expanded uncertainty (0.01–0.02 cm³/cm³ depending on moisture) was established along with calibration of the applied sensor. The obtained values are comparable to, or even better than, the features of the traditional invasive sensors utilizing universal calibration models. Both, the TDR and capacitive (FD) sensor enabled monitoring of capillary uptake phenomenon progress. It was noticed that at the end of the experiment the TDR readouts were 4.4% underestimated and the FD readouts were overestimated for 12.6% comparing to the reference gravimetric evaluation.

The aim of the research that is presented in this paper was to evaluate the physical and mechanical properties of heat-insulating mortars with expanded cork aggregates and different binders. In this work, the measurements of surface roughness and adhesion strength, supported by determination of basic mechanical and physical parameters, such as density, bulk density, open porosity, total porosity, absorbability, thermal conductivity coefficient, compressive strength, flexural strength, and frost resistance of mortars containing expanded oak cork, were performed. The scanning electron microscope (SEM) investigations demonstrated the microstructure, contact zone, and distribution of pores in the heat-insulating mortars containing expanded cork. The results indicated that the addition of expanded cork and different binders in heat-insulating mortars triggers changes in their roughness and adhesion strength. The SEM research confirmed the very good adhesion of the paste to the cork aggregate.

Recent climate changes limiting the available water resources require careful sustainable water management in the cities, the locations of highest drinking water consumption and sanitary sewage and stormwater generation. Over 50% of water demand in the residential areas of cities cover activities in which non-potable water could be used, e.g., toilets and laundry facilities, cleaning, garden irrigation and washing vehicles. Thus, rain water harvesting (RWH) systems are the sustainable alternative water supply, lowering drinking water consumption, by the usage of non-potable harvested water, and limiting the anthropopressure on natural water reservoirs. However, in many cases the social acceptance of RWH and willingness to pay may be affected by financial sustainability, including the affordability and profitability of the investment. This paper presents a case study concerning the financial sustainability of thirteen designs of RWH systems for a single-family house under the climatic and economic conditions of Eastern Poland, one of the poorest regions of the European Union. The financial sustainability of the tested RWH designs were based on indictors of cost-efficiency: dynamic generation cost, payback period, net present value and benefit–cost ratio. The performed analyses showed the limited profitability of the studied RWH designs and the insufficient governmental financial support which may significantly affect the social sustainability of the designs under the local conditions.

This paper presents a study assessing the possible application of seven clay substrates of various particle compositions and plasticity, sampled locally in rural regions, as materials allowing affordable construction of the waste landfill liners, which meet the main principles of sustainability, utilize locally available materials and limit the environmental threats posed by landfill leachate to water, public health and arable land. The researched substrates were tested according to their long-term sealing properties by their saturated hydraulic conductivity after compaction, swelling and shrinkage characteristics and ability to sustain their sealing capability after repeated drying and rewetting. The basic characteristics of soils were determined by the standard methods. Saturated hydraulic conductivity after compaction and after repeated shrinking and swelling were tested in laboratory falling head permeameters. Shrinkage characteristics were based on dimensionless indicators of the geometry and linear extensibility. The obtained results showed that the tested clay substrates were found applicable to construction of compacted clay liner for sustainable waste landfill. The environmental sustainability of a local, rural waste landfill, isolated by compacted earthen liners utilizing local materials is, in our opinion possible, but strongly related to the compaction parameters applied during liner construction for the given clay substrate.

We studied the effect of climate variations on the structure of the assemblage of ground beetles (Coleoptera: Carabidae) in a wetland and surrounding watershed forest. We analyzed the changes in the structure of the assemblage of ground beetles provoked by a two-year dry period against the background of studies carried out during the two-year wet period. Aridization influenced the structure of the assemblage of ground beetles more in wetlands than in forests. It was shown that despite the stabilizing effect of the forest on the structure of assemblages of terrestrial arthropods, the two-year dry period had a negative impact on the assemblage of ground beetles in the studied area. The Simpson dominance index of 4.9 during the wet season increased to 7.2 during the drought period. Although the total number of species during the dry period did not significantly decrease in comparison with the wet period—from 30 to 27 species—changes occurred in the trophic structure: during the drought period, the number of predators decreased. It is concluded that the resistance of forest habitats to climate aridization is somewhat exaggerated and, very likely, the structure of the community of arthropods in forests will change significantly.

The aim of the research presented in this paper is to evaluate the feasibility of using hydrophobic agents based on organosilicon compounds for surface protection of lightweight concrete modified with waste polystyrene. The experimental part pertains to the physical and mechanical properties of polystyrene-modified lightweight concrete. The concrete samples were prepared with the following ingredients: CEM I 42.5 R cement, recycled polystyrene (0–2 mm), quartz sand (0–2 mm), coarse river aggregate (2–16 mm), and water. Silane and tetramethoxysilane were employed for surface hydrophobization. Concrete with 20% polystyrene exhibits high porosity (25.22%), which is related to an increase in absorptivity (14.75%) compared to the reference concrete. The hydrophobized concrete is characterized by the lowest surface free energy (SFE) value, which is 7 or 11 times lower than the value of reference concrete, depending on the agents. The test on the contact angle (CA) was performed before and after the frost-resistance test (F–T test). Lower SFE translates into lower adhesive properties, higher resistance of the material to the infiltration of water and corrosive compounds, e.g., salts, and higher resistance to freezing and thawing cycles. Silane and tetramethoxysilane coating raised frost resistance by 54–58% compared to the reference samples. This agent reduced absorptivity by 30%. Recycled polystyrene can be successfully used to produce lightweight concrete (LC) with high durability provided by hydrophobic/icephobic coatings.