The work is devoted to the research of precision regularities in a spindle unit by the trajectory of the spindle installed on hydrostatic bearings. The mathematical model of trajectories spindle with lumped parameters that allows to define the position of the spindle with regard the simultaneous influence of design parameters, geometrical deviations ofform, temperature deformation bearing surfaces, the random nature of operational parameters and technical loads of hydrostatic bearings has been developed. Based on the results of numerical modeling the influence of shape errors of bearing surface of hydrostatic bearing on the statistical characteristics of the radius vector trajectories of the spindle by varying the values rotational speed of the spindle and oil pressure in front hydrostatic bearing has been developed. The obtained statistical regularities of precision spindle unit have been confirmed experimentally. It has been shown that an effective way to increase the precision of spindle units is to regulate the size of the gap in hydrostatic spindle bearings. The new design of an adjustable hydrostatic bearing, which can improve the accuracy of regulation size gap has been proposed.
Promising ways of energy efficiency gain of spindles with fluid flow bearings are offered. New design of journal hybrid flow bearing which contains spherical bearing pockets and adjustable valves with relay control system is offered to improve energy efficiency of spindle units of machine tools. To reduce power losses of fluid bearings at high speed special lubrication based on water with integrated system of corrosion protection is offered. Results of theoretical research of energy consumption of grinding machine tool with a new design of spindle hybrid bearings are presented. Power losses of the spindle unit with both new design and base design of journal bearings are assessed. Effectiveness of new design of spindle hybrid bearings at high operating speeds is shown.
The analysis of spatial functions of pressure considering the geometrical deviations and the elastic deformation of conjugate surace have been considered. The analysis of spatial functions of pressure is performed by the finite element method. The difference of the size of pressure in a tangential direction of a pocket of a support under various service conditions has been investigated. A recommendation for improving of operational characteristics in regulated hydrostatic radial bearing has been developed.
Chatter accompanies the cutting process and is the main obstacle to achieving precision and productivity in milling operations. To reduce the amplitude of vibrations, it was proposed to use a stability lobes diagram (SLD) when assigning cutting modes. The machining system in end milling was represented by a two-mass dynamic model in which each mass has two degrees of freedom. The behavior of such a system was described by a structure with two inputs, in-depth and cutting feed, and a delay in positive feedback on these inputs. A new criterion was applied to design the SLD based on an analysis of the location of the machining system Nyquist diagram on the complex plane. The algorithm for designing a stability chart was developed into an application program, a tool for the technologist-programmer when assigning cutting modes. A method for parameter identification necessary for designing the dynamic system “tool – workpiece” was proposed. The effectiveness of the developed method was proven experimentally when the choice of spindle speed during end milling allows one to reduce the roughness parameter Ra from 3.2 µm to 0.64 µm at the same feed rate of 650 mm/min.
1 January 2020 in TECHNICAL SCIENCES AND TECHNOLOGIES
Актуальність теми дослідження. Технологічне підготовлення виробництва є важливим етапом, оскільки саме на ньому розробляється технологічний процес (ТП) виготовлення деталі, від якого залежать техніко-економічні показники, які визначають конкурентоспроможність деталі на ринку продукції. Постановка проблеми. Час, який витрачається багатьма вітчизняними підприємствами на розрахунок техніко-економічних показників технологічного процесу виготовлення деталі, сьогодні є досить значним, що суттєво сповільнює технологічне підготовлення виробництва. У сучасних умовах швидкості навколишніх змін, перетворень та конкуренції на ринку це недопустимо. Аналіз досліджень і публікацій. Нині є значна кількість програмного забезпечення для розрахунку технікоекономічних показників ТП виготовлення деталей. Кожна програма має свої переваги і недоліки. Виділення недосліджених частин загальної проблеми. Важливим елементом програмного забезпечення для розрахунку техніко-економічних показників ТП виготовлення деталей має бути можливість оперативного розрахунку оптимального ТП за показниками, які є найбільш важливими в конкретних виробничих умовах. Тобто має бути можливість вибору параметра оптимізації. Метою статті є удосконалення методу розрахунку вартості та часу виготовлення деталі залежно від типу виробництва. Виклад основного матеріалу. На прикладі конкретної деталі, продемонстровано можливості програмного забезпечення «Auto_price» для розрахунку вартості деталі, залежно від типу виробництва і структури технологічного процесу. Вибрано оптимальне рішення, враховуючи вартість та час виготовлення, зважаючи на ваговий коефіцієнт, який було обрано за допомогою експертної оцінки. Висновки відповідно до статті. У роботі було удосконалено метод розрахунку вартості та часу виготовлення деталі залежно від типу виробництва, що дозволило отримати оптимальний технологічний процес з урахуванням техніко-економічних показників та реалізувати цей метод програмно.