Yuri Petrakov

Yuri Petrakov

Auto-generated profile, based on publicly available information

Yuri Petrakov

National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 December 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
YPYuri Petrakov
Yuri Petrakov
MDMariia Danylchenko
Mariia Danylchenko
This paper reports a new approach to ensuring the stability of the turning process, which is based on the frequency-time characteristics of the technological machining system (TMS). The approach uses a mathematical model of the turning process as a single-mass system with one degree of freedom, taking into account negative feedback on the normal coordinate and positive feedback with a delay in cutting depth. A new criterion for the stability of the cutting process as a system with a delay in positive feedback is proposed, based on the analysis of frequency characteristics in the form of a Nyquist diagram. It is proved that such a system will be stable when the chart of its Nyquist diagram does not cover a point with coordinates [+1, 0] on the complex plane. The validity of the new criterion has been confirmed by comparing the simulation results in the time range with the location of the Nyquist diagram on the complex plane. Based on the new criterion of stability, an algorithm for automatic construction of a Stability Lobes Diagram (SLD) has been developed. The necessary a priori parameters of TMS, the ranges of frequency change, and the calculation step for constructing such a characteristic in the coordinates "cutting depth – spindle rotational speed" have been determined. The adequacy of the obtained results is confirmed by a full-scale experiment to assess the roughness of machined parts under cutting modes that fall into the area of stability and instability on the SLD chart. The full-scale experiment proved the possibility of a significant reduction in roughness according to the Rz parameter, from 43 µm to 18 µm, while increasing productivity by 1.28 times. The use of a stability lobes diagram is especially effective when programming CNC lathes where it is possible to select the spindle speed in a wide range.

28 April 2022 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
YPYuriy Petrakov
Yuriy Petrakov
VKVolodymyr Korenkov
Volodymyr Korenkov
AMArtur Myhovych
Artur Myhovych
This paper reports a new technology for designing control programs for contour milling on CNC machines. The technology enables stabilization of the cutting process along the entire contour at the optimal level by controlling the feed, which ensures an increase in productivity when meeting the requirements for restrictions. Moreover, the effectiveness of using the technology improves with an increase in the complexity of the contour by changing the curvature of the surface. A mathematical model has been built for the interaction between the cutter and workpiece in the cutting zone when machining contours with variable curvature, which makes it possible to determine the main characteristic of the cutting process – the rate of cutting the allowance. The technology involves the use of a control program in G codes designed in any CAM system. At the first stage, a shape-formation trajectory in the form of a two-dimensional digital array is derived from the program. At the second stage, the cutter workpiece engagement in the cutting area is modeled simulated while determining the main characteristic of the cutting process – an analog of the material removal rate. And at the final stage, the simulation results are used to design a new control program, also in G-codes, with a new recorded law to control the feed, which enables the stabilization of the cutting process along the entire milling path. The software for the new technology has been developed, which automatically converts the preset control program in G-codes into a two-dimensional digital array, simulates the milling process, and designs a new control program in G-codes based on its results. The results of the experimental study into the milling of the preset contour using the developed simulation program showed an increase in productivity by 1.7 times compared to the original control program, designed in a conventional CAM system

1 January 2023 in Journal of Engineering Sciences
Verified
Journal Article
Open access
YPYuri Petrakov
Yuri Petrakov
OOOleksandr Okhrimenko
Oleksandr Okhrimenko
MSMaksim Sikailo
Maksim Sikailo
AMArtur Myhovych
Artur Myhovych
The cutting force in end milling is the essential perturbation of the machining system that limits the productivity of the process. Therefore, forecasting the cutting force when assigning the processing mode and the geometry of the allowance layer to be cut is an urgent task that requires an operational tool for its solution. The method of calculating the cutting force is presented, based on a mechanistic approach, when the geometric ratios of the cutter blades’ positions on the sweep determine the thickness of the undeformed chip. The developed algorithm calculates the cutting force by double integration, first by the length of the cutting edge and then by the number of such edges. The algorithm also allows the simulating of the outrun of the mill on the cutting force and its components. The created application program visualizes the simulating process by oscillograms of the cutting force components for both up and down milling. Experimental studies, in general, proved the adequacy of the developed modeling method. The created program is a tool for operational forecasting of the cutting force during the technological preparation of the end milling process in production.

8 April 2019 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
YPYuri Petrakov
Yuri Petrakov
DSDanylo Shuplietsov
Danylo Shuplietsov
Contour milling programming technology for virtual basing on a CNC machine

1 September 2020 in Mechanics and Advanced Technologies
Verified
Journal Article
Open access
PDF file
YPY. V. Petrakov
Y. V. Petrakov
АMА. V. Myhovych
А. V. Myhovych
Recognizing the practical need to control the cutting process, leading firms in the high-tech market began to offer software products that, in the automatic mode, were said to be able to calculate the optimal cutting mode. Currently, the most advanced technology is called iMachining, which means intelligent Machining. The article presents an analysis of the control, automatically designed in the iMachining Solid CAM module, for machining a test part, the contour of which is formed by two straight circular arcs of a circle. It is shown that when designing control, geometric criteria are used that are associated with the path of shaping, so stabilization of the cutting process is not achieved. A control design method is proposed based on the results of simulation the Material Removal Rate (MRR), which allows stabilizing the cutting process.

23 May 2023
Verified
Book Chapter
Closed access
PDF file
YPYuri Petrakov
Yuri Petrakov
YDYuri Danylchenko
Yuri Danylchenko
SSSerhii Sapon
Serhii Sapon
MSMaksim Sikailo
Maksim Sikailo