1 January 2023 in Journal of Engineering Sciences
The cutting force in end milling is the essential perturbation of the machining system that limits the productivity of the process. Therefore, forecasting the cutting force when assigning the processing mode and the geometry of the allowance layer to be cut is an urgent task that requires an operational tool for its solution. The method of calculating the cutting force is presented, based on a mechanistic approach, when the geometric ratios of the cutter blades’ positions on the sweep determine the thickness of the undeformed chip. The developed algorithm calculates the cutting force by double integration, first by the length of the cutting edge and then by the number of such edges. The algorithm also allows the simulating of the outrun of the mill on the cutting force and its components. The created application program visualizes the simulating process by oscillograms of the cutting force components for both up and down milling. Experimental studies, in general, proved the adequacy of the developed modeling method. The created program is a tool for operational forecasting of the cutting force during the technological preparation of the end milling process in production.
27 December 2021 in Mechanics and Advanced Technologies
This paper proposes a method for determining the parameters of a single-lane hyperboloid as the initial tool surfaces of finger modular mills for large-modular gears and design dependences for determining the parameters of a hyperboloid in which the deviation of its curvilinear axial profile will be minimal from the involute curve. The influence of the gear module and the number of teeth and the theoretical deviations from the involute profile that can be achieved with this method of replacing the original tool surface are calculated and studied. Recommendations for design are given and the design of schemes of cutting and cutting part of a finger mill on the basis of a hyperboloid at their realization by non-grinding carbide plates of rectangular form is offered that considerably improves manufacturability of production of such mills and reduces their cost. The advantages and disadvantages of such tools, which are made on the basis of hyperboloid in comparison with the tools of standard designs, are determined.
26 December 2024 in Mechanics and Advanced Technologies
Cutting processes are carried out in an elastic machining system, which is multi-mass with negative and positive loop control with a delay in construed mathematical models. Its behavior during the cutting process is entirely determined by dynamic properties and an adequate parameters of mathematical model is necessary to control the process. The paper proposes a method for identifying such dynamic parameters of the machining system, which include natural vibration frequencies, vibration damping coefficients, and stiffness of the replacement model of single-mass system in the direction of the machine-CNC coordinate axes. It is proposed to identify such parameters as a result of experimental modal analysis by impacting the elements of the tool and workpiece with an impact hammer and processing the impulse signal with a fast Fourier transform. It is proposed to adapt the results obtained to the adopted mathematical model of the machining system, presented in the form of two masses, each with two degrees of freedom, according to the equivalence of the spectrum signal power or its spectral density. The cutting force model in the form of a linearized dependence on the area of undeformed chips needs to be clarified by the coefficient using experimental oscillograms obtained during milling of a workpiece mounted on a dynamometer table. Based on the identified parameters of the machining system, a stability diagram was constructed in the “spindle speed – feed” coordinates and experiments were carried out under conditions in the zone of stable and unstable cutting. Evaluation of the roughness of the machined surface confirmed the correspondence to the location of the stability lobes diagram constructed using the identified parameters, which indicates the effectiveness of the proposed identification method.
28 July 2022 in Bulletin of the National technical university "Kharkiv Polytechnic Institute" Series: Techniques in a machine industry
MHMagomedemin Isamagomedovich Hasanov
Magomedemin Isamagomedovich Hasanov
AZAlexander Yuryevich Zakovorotnіy
Alexander Yuryevich Zakovorotnіy
ВФВіталій Сергійович Федоренко
Віталій Сергійович Федоренко
The scientific foundations of the technological regulation for the selection and assignment of processing parameters during gear milling are based on the fundamental theoretical provisions of the friction theory, mechanical engineering technology and cutting theory. For the first time, the sliding angle was scientifically substantiated during plastic displacement (pre-deformation) of the material, when the material flows around the indenter (tool) without separation from the main mass. Determination of the minimum sliding angles during the processing of large-module gear wheels by milling, based on the physicochemical processes of friction mechanics, can significantly increase the efficiency of the tooth shaping process and the operational properties of their surfaces. An atomic approach to the processes of deformation and destruction of chips during cutting is presented. The resistance to plastic deformation of the cut layer depends on the type of crystal lattice of the processed material, its stacking fault energy, and the presence of impurities at the grain boundaries. The influence of these factors is manifested through the types of dissipative structures that are formed in the process of deformation of the cut layer and determine its localization.
1 January 2024 in Journal of Engineering Sciences
Chatter accompanies the cutting process and is the main obstacle to achieving precision and productivity in milling operations. To reduce the amplitude of vibrations, it was proposed to use a stability lobes diagram (SLD) when assigning cutting modes. The machining system in end milling was represented by a two-mass dynamic model in which each mass has two degrees of freedom. The behavior of such a system was described by a structure with two inputs, in-depth and cutting feed, and a delay in positive feedback on these inputs. A new criterion was applied to design the SLD based on an analysis of the location of the machining system Nyquist diagram on the complex plane. The algorithm for designing a stability chart was developed into an application program, a tool for the technologist-programmer when assigning cutting modes. A method for parameter identification necessary for designing the dynamic system “tool – workpiece” was proposed. The effectiveness of the developed method was proven experimentally when the choice of spindle speed during end milling allows one to reduce the roughness parameter Ra from 3.2 µm to 0.64 µm at the same feed rate of 650 mm/min.
31 October 2023 in Eastern-European Journal of Enterprise Technologies
This paper reports a new approach to ensuring the stability of the end milling process, due to vibration-free cutting modes, which are determined from the stability lobes diagram of the dynamic machining system. An application program for automatic calculation of the stability lobes diagram in the coordinates «mill spindle speed – feed» has been developed, which is a tool for the technologist-programmer when designing control program for numerically controlled machines. The mathematical model underlying the application program represents a dynamic machining system as a single-mass system with two degrees of freedom, covered by negative feedback in the direction of two coordinates. The trailing machining is represented as positive feedback loops with a delay function in each. The mathematical model is given in the form of state variables, which allows applying numerical modeling methods to determine both transient and frequency responses. The software developed includes a separate module for automatic design of the stability lobes diagram whose algorithm uses the features of the location of the Nyquist diagram on the complex plane. Since the functioning of the developed program requires a priori information about the dynamic parameters of the machining system, a procedure for their experimental identification is presented. The stiffness of the machining system in two coordinates was determined with the help of a dynamometer, and the frequency responses were determined by the impulse response function, which was obtained with an impact hammer. The research results were confirmed experimentally both by computer simulation and milling on a machine tool and could be recommended for determining the cutting mode at end milling