IZZAWATI BASIROM

Dr. IZZAWATI BASIROM


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 October 2017 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
IBIZZAWATI BASIROM
IZZAWATI BASIROM
RDR Daud
R Daud
MAM Afendi
M Afendi
AMAman Shah Majid
Aman Shah Majid
NZN A M Zain
N A M Zain
YBY Bajuri
Y Bajuri
Internal fixation is a mechanism purposed to maintain and protect the reduction of a fracture. Understanding of the fixation stability is necessary to determine parameters influence the mechanical stability and the risk of implant failure. A static structural analysis on a bone fracture fixation was developed to simulate and analyse the biomechanics of a diaphysis shaft fracture with a compression plate and conventional screws. This study aims to determine a critical area of the implant to be fractured based on different implant material and angle of fracture (i.e. 0°, 30° and 45°). Several factors were shown to influence stability to implant after surgical. The stainless steel, (S. S) and Titanium, (Ti) screws experienced the highest stress at 30° fracture angle. The fracture angle had a most significant effect on the conventional screw as compared to the compression plate. The stress was significantly higher in S.S material as compared to Ti material, with concentrated on the 4th screw for all range of fracture angle. It was also noted that the screws closest to the intense concentration stress areas on the compression plate experienced increasing amounts of stress. The highest was observed at the screw thread-head junction.

30 August 2023 in Materials
Verified
Journal Article
Open access
PDF file
IBIZZAWATI BASIROM
IZZAWATI BASIROM
RDRUSLIZAM DAUD
RUSLIZAM DAUD
MIMuhammad Farzik Ijaz
Muhammad Farzik Ijaz
MRMohd Afendi Rojan
Mohd Afendi Rojan
KBKhairul Salleh Basaruddin
Khairul Salleh Basaruddin
An understanding of the biomechanical characteristics and configuration of flexible and locked plating in order to provide balance stability and flexibility of implant fixation will help to construct and promote fast bone healing. The relationship between applied loading and implantation configuration for best bone healing is still under debate. This study aims to investigate the relationship between implant strength, working length, and interfragmentary strain (εIFM) on implant stability for femoral midshaft transverse fractures. The transverse fracture was fixed with a fragment locking compression plate (LCP) system. Finite element analysis was performed and subsequently characterised based on compression loading (600 N up to 900 N) and screw designs (conventional and locking) with different penetration depths (unicortical and bicortical). Strain theory was used to evaluate the stability of the model. The correlation of screw configuration with screw type shows a unicortical depth for both types (p < 0.01) for 700 N and 800 N loads and (p < 0.05) for configurations 134 and 124. Interfragmentary strain affected only the 600 N load (p < 0.01) for the bicortical conventional type (group BC), and the screw configurations that were influenced were 1234 and 123 (p < 0.05). The low steepness of the slope indicates the least εIFM for the corresponding biomechanical characteristic in good-quality stability. A strain value of ≤2% promotes callus formation and is classified as absolute stability, which is the minimum required value for the induction of callus and the maximum value that allows bony bridging. The outcomes have provided the correlation of screw configuration in femoral midshaft transverse fracture implantation which is important to promote essential primary stability.

25 August 2019 in Malaysian Journal of Fundamental and Applied Sciences
Verified
Journal Article
Open access
PDF file
IBIZZAWATI BASIROM
IZZAWATI BASIROM
MRMohd Afendi Rojan
Mohd Afendi Rojan
MMM.S. Abdul Majid
M.S. Abdul Majid
NZNor Alia Md Zain
Nor Alia Md Zain
MBMohd Yazid Bajuri
Mohd Yazid Bajuri
Implant screws failure commonly occurs due to the load that constantly generated by the patient’s body to the fracture area. Bending load is often encountered in femur bone due to lateral impact which affected the bone and also the implants installed. Consequently, the load will lead to the failure of implants that can cause loosening or tightening of implants. Henceforth, in this manner, it is significant to study the bending behavior of bone implant in femur bone. The aim of this study was to analyze the stress shielding of bone implant on the internal fixator. 3D technique is able to show the overall deformation and stress distribution. The lower the biomechanical compatibility, the lower the STP value obtained. In addition, the variation of elastic modulus (E) of the screws materials, 200GPa (Stainless Steel) and 113.8GPa (Titanium) resulted in the increase of the total stress transferred (STP) between screw and bone interface. In this work, strain energy density (SED) was determined as a good indicator of stress shielding.

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
IBIZZAWATI BASIROM
IZZAWATI BASIROM
RDRUSLIZAM DAUD
RUSLIZAM DAUD
MAM. Afendi
M. Afendi
MMM.S. Abdul Majid
M.S. Abdul Majid
NZNoor Alia Md Zain
Noor Alia Md Zain
Finite element models have been widely used to quantify the stress analysis and to predict the bone fractures of the human body. The present study highlights on the stress analysis of the homogeneous structure of human femur bone during standing up condition. The main objective of this study is to evaluate and understand the biomechanics for human femur bone and to prepare orthotropic homogeneous material models used for FE analysis of the global proximal femur. Thus, it is necessary to investigate critical stress on the human femur bone for future study on implantation of internal fixator and external fixator. The implication possibility to create a valid FE model by simply comparing the FE results with the actual biomechanics structures. Thus, a convergence test was performed by FE model of the femur and the stress analysis based on the actual biomechanics of the human femur bone. An increment of critical stress shows in the femur shaft as the increasing of load on the femoral head and decreasing the pulling force at greater trochanter.