Pure BiFeO3 (BFO) and doped Bi0.9La0.1FeO3 (BLFO) thin films were prepared on Pt/TiO2/SiO2/Si substrates by a modified sol–gel technique using a separate hydrolysis procedure. The effects of final crystallization temperature and La doping on the phase structure, film morphology, and nanoscale piezoelectric properties were investigated. La doping and higher crystallization temperature lead to an increase in the grain size and preferred (102) texture of the films. Simultaneously, a decrease in the average effective piezoelectric coefficient (about 2 times in La-doped films) and an increase in the area of surface non-polar phase (up to 60%) are observed. Phase separation on the films’ surface is attributed to either a second phase or to a non-polar perovskite phase at the surface. As compared with undoped BFO, La-doping leads to an increase in the average grain size and self-polarization that is important for future piezoelectric applications. It is shown that piezoelectric activity is directly related to the films’ microstructructure, thus emphasizing the role of annealing conditions and La-doping that is frequently used to decrease the leakage current in BFO-based materials.
Herein we report on the synthesis and the effects of gradual loading of TiO2 nanotube array layers with ZnO upon surface wettability. Two-step preparation was chosen, where TiO2 nanotube layers, grown in a first instance by anodization of a Ti foil, were gradually loaded with controlled amounts of ZnO using the reactive RF magnetron sputtering. After crystallization annealing, the formerly amorphous TiO2 nanotubes were converted to predominantly anatase crystalline phase, as detected by XRD measurements. The as-prepared nanotubes exhibited a well-aligned columnar structure, 1.6 μm long and 88 nm in diameter, and a small concentration of oxygen vacancies. Ti2+ and Ti3+ occur along with the Ti4+ state upon sputter-cleaning the layer surfaces from contaminants. The Ti2+ and Ti3+ signals diminish with gradual ZnO loading. As demonstrated by the VB-XPS data, the ZnO loading is accompanied by a slight narrowing of the band gap of the materials. A combined effect of material modification and surface roughness was taken into consideration to explain the evolution of surface super-hydrophilicity of the materials under UV irradiation. The loading process resulted in increasing surface wettability with approx. 33%, and in a drastic extension of activation decay, which clearly points out to the effect of ZnO-TiO2 heterojunctions.
1 January 1999 in Journal of Inclusion Phenomena and Macrocyclic Chemistry
In this work, we have investigated the photocurrent and spectral sensitivity of the silicon/SrTiO3:xNb/perovskite structures. The sol–gel method carried out the deposition of undoped SrTiO3 layers as well as niobium-doped (SrTiO3:Nb) layers at atomic concentrations of 3 and 6% Nb. The perovskite layer, CH3NH3PbI3−xClx, has been deposited by the vacuum co-evaporation technique. The layers have been characterized by scanning electron microscopy and X-ray diffraction measurements. The volt–ampere characteristics and spectral sensitivity of the fabricated samples have been measured under illumination with selective wavelengths of 405, 450, 520, 660, 780, 808, 905, 980, and 1064 nm of laser diodes. We have shown that for different configurations of applied voltage between silicon, SrTiO3:xNb, and CH3NH3PbI3−xClx, the structures are photosensitive ones with a variation of photocurrent from microamperes to milliamperes depending on Nb concentration in SrTiO3, and the highest photocurrent and spectral sensitivity values are observed when a SrTiO3:Nb layer with 3 at.% of Nb is used. A possible application of the proposed structure with a SrTiO3:Nb layer for perovskite solar cells and photodetectors is being discussed.