Artificial construction of a weakening zone over the roadway is an essential method for preventing coal bursts and rock bursts caused by strong mining tremors. However, concerning the seismic absorption and load reduction capabilities of an artificial structural weakening zone, the degree of rock mass damage to the roadway under weakening zone protection remains unclear. This study employed principles of elasticity and UDEC (Universal Distinct Element Code) to explore the seismic attenuation and load reduction capabilities of the weakening zone. The results indicate that the absorbing ability of the weakening zone increases exponentially with its weakening coefficient. Under the same dynamic load disturbance, when the weakening coefficient rises from 0.00 to 0.99, the sidewall displacement from the elastic wave source side changes from 0.400 m to 0.228 m. The total number of cracks in the roadway-surrounding rock, and the ranges of overstressed zones decreased linearly. The critical threshold of the roadway resisting the mining tremor disturbance increased. In particular, when the mining tremor is located directly above the roadway, the initial deformation of the roof is the largest, and the cumulative deformation of the rib is greater than the roof. By creating a weakening zone with a coefficient exceeding 0.95, the roadway remains unaffected by the 20 MPa dynamic loading. The study provides a theoretical basis for controlling coal burst that is triggered by mining tremors.
16 August 2024 in Energy Exploration & Exploitation
During underground coal mining, Mining-induced seismicity is a crucial factor leading to roadway deformation. Based on a case study of rib spalling caused by mining-induced seismicity in China, this paper utilizes the Universal Distinct Element Code to investigate the mechanism of rib spalling. It analyzes the stress evolution process of roadway surrounding rock and the damage process under the influence of mining-induced seismicity. Additionally, it examines the relationship between seismic wave amplitude, frequency and the damage characteristics of roadway surrounding rock. Findings show that seismic waves induce stress concentration zones in the deeper surrounding rock, causing shear failure, while stress concentration zones emerge in the top, bottom and shoulders of roadway, leading to tensile failure in the shallower surrounding rock. With increasing seismic wave amplitude, the critical crack length of surrounding rock decreases, resulting in a linear increase in crack count and distribution area. The roadway exhibits a ‘n'-shaped damage profile primarily driven by shear failure. With increasing seismic wave frequency, the crack count in the surrounding rock of the roadway exhibits a trend of initially increasing and then decreasing. This trend becomes more pronounced with larger amplitudes. Rib spalling damage is influenced by seismic wave frequency and amplitude: frequencies of 20–25 Hz and 80–100 Hz require amplitudes exceeding 3 m for damage, while 25–30 Hz and 55–80 Hz require amplitudes over 2 m, and 30–55 Hz necessitate amplitudes exceeding 1.5 m.
A combination of theoretical analysis, numerical simulation and physical model experiments is used to explore the mechanism of pressure relief and roof blasting effects along the gob-side roadway. The stress and displacement along the gob-side roadway before and after blasting were investigated using discrete unit code (UDEC) software. The results demonstrated that blasting can effectively decrease the peak stress of the coal seam along the gob-side roadway and transfer it to the depth. The maximum displacement of the roof of the gob-side roadway, the coal pillar and the solid coal was reduced from 9.5, 10.8 and 4 cm to 6.5, 2 and 3 cm, respectively, after roof blasting. The experimental results showed that the movement of the overburden strata showed obvious regional characteristics after blasting which included the height of the caving zone on the broken side being 3.3 times higher than that observed on the unbroken side, while the height of the fractured zone was 0.52 times higher. The field application of roof blasting was controlled by a drilling method, micro-seismic monitoring and stress monitoring. The results showed good application effects. This research provides valuable insights for managing the stability of gob-side entries.
In practice, the bending and fracturing of heavy layers is often considered the primary cause of surface damage, leading to significant environmental impacts, whereas heavy layer-type mining-induced earthquakes are frequently overlooked. This study combines theoretical analysis, UDEC numerical simulations, and industrial experiments to investigate the dynamic behavior of heavy layers and the mechanisms through which mining-induced earthquakes trigger surface damage. It aims to demonstrate that heavy layer movement and mining-induced earthquakes cause surface damage and to develop a replicable engineering solution for seismic prevention and subsidence control in heavy layer mining areas. The results reveal that surface damage stems from the synergistic effects of heavy layer fracturing and associated mining-induced earthquakes, where bending subsidence from heavy layer fracturing is the primary driver, and mining-induced earthquakes act as a secondary factor by compressing fragmented rock pores to amplify overlying layer subsidence. Industrial tests at the 7202 working face using deep-hole roof pre-splitting blasting successfully fractured the heavy conglomerate layer, enhanced goaf bulking, and reduced the intensity of layer movement. This intervention significantly decreased the frequency and energy of mining-induced earthquakes, mitigating surface damage. These findings provide a practical framework for the integrated control of mining-induced earthquakes and subsidence in heavy layer environments.