Radomila Konecna

Prof. Radomila Konecna

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
RKRadomila Konecna
Radomila Konecna
TVTibor Varmus
Tibor Varmus
GNGianni Nicoletto
Gianni Nicoletto
MJMichal Jambor
Michal Jambor
Additive manufacturing of high strength Al alloys brings problems with hot cracking during rapid solidification. One of the ways to solve this challenge is technology developed by the Elementum 3D company. The way consists of inoculation by ceramic nanoparticles using RAM technology. When applying the L-PBF method, a very fine equiaxed microstructure with exceptional properties and without cracks is created. This paper offers the results and discussion of the microstructure, surface roughness and fatigue life of the high-strength Al2024-RAM2 alloy made from a gas atomized powder with an additive of 2 wt.% ceramic nanoparticles on the base of Ti. The specimens for fatigue tests were produced in different orientations relative to the building platform and left in the as-built conditions with different surface quality (roughness). The specimens were T6 heat-treated. The treatment caused a coarsening of a part of the fine grains. After T6 heat treatment, the hardness increased significantly, which occurred by precipitation hardening. Fatigue tests of specimens with different build orientation were performed in plane bending and the experimentally determined fatigue life was discussed in terms of surface roughness and material microstructure.

25 June 2014 in Procedia Engineering
Verified
Journal Article
Open access
PDF file
RKRadomila Konecna
Radomila Konecna
GNG. Nicoletto
G. Nicoletto
LKL. Kunz
L. Kunz
MSM. Svoboda
M. Svoboda
ABA. Bača
A. Bača
The strengthening mechanism based on the formation of precipitates (Guinier-Preston (GP) zones) during decomposition of a metastable supersaturated solid solution is stable and effective below temperatures, which are typically overcome in the piston region facing the combustion chamber. Therefore, pistons experience a progressive loss of strength due to over-aging during service. This contribution reports of a structural investigation on a eutectic AlSi12CuNiMg alloy before and after fatigue testing at high temperatures (up to 350 °C). Metallography, color etching, SEM and TEM are used to elucidate the following aspects: 1) the structural features of the alloy (dendrites of α−phase, primary Si particle size and distribution, morphology and distribution of intermetallic phases); 2) the evolution of the strengthening mechanism (GP zones) with high temperature exposure.

1 September 2015 in Manufacturing Technology
Verified
Journal Article
Open access
PDF file
ABAdrián Bača
Adrián Bača
RKRadomila Konecna
Radomila Konecna
GNGianni Nicoletto
Gianni Nicoletto
LKLudvík Kunz
Ludvík Kunz
Direct Metal Laser Sintering enables production of fully dense metal parts with comparable or higher tensile properties as compared to the conventionally produced parts. However, for a more widespread use of this additive manufacturing techniq...

1 December 2019 in Production Engineering Archives
Verified
Journal Article
Open access
PDF file
RKRadomila Konecna
Radomila Konecna
DMDenisa Medvecká
Denisa Medvecká
GNGianni Nicoletto
Gianni Nicoletto
Additive manufacturing has recently expanded its potential with the development of selective laser melting (SLM) of metallic powders. This study investigates the relation between the mechanical properties and the microstructure of Ti6Al4V alloy produced by SLM followed by a hot isostatic pressing (HIP) treatment. HIP treatment minimizes the detrimental influence of material defects. Tensile specimens produced with reference to specific building axes were prepared using a Renishaw A250 system. It has been found that the tensile strength and elongation depend on specimen building direction. Microstructural and textural characterizations were carried out to identify the source of differences.

21 April 2022 in Engineering Manufacturing Letters
Verified
Journal Article
Open access
PDF file
FUFederico Uriati
Federico Uriati
GNGianni Nicoletto
Gianni Nicoletto
EREnrica Riva
Enrica Riva
TVTibor Varmus
Tibor Varmus
RKRadomila Konecna
Radomila Konecna
The fatigue performance of materials, such as Inconel 718, when produced by Laser Powder Bed fusion, needs to be fully understood to manage and exploit the full potential of this Additive Manufacturing technology. Microstructure and as-built surface morphology are strictly related to process parameters and are known to affect the fatigue response. The present contribution examines experimentally the fatigue behavior of laser powder bed fused Inconel 718 testing specimens printed along three different orientations with respect to the built direction. The observed directional fatigue behavior is discussed in terms of surface quality, near-surface microstructure and their interaction with the fatigue crack initiation mechanisms.