Carbohydrate biomass can be employed as a reductant for metallic material preparation due to it possessing diverse reducing functional groups. The reported studies focused on reduction of metal ions in acidic solution with the aid of biomass. However, we found alkali hydrothermal conditions are favorable to metal compound reduction, even direct conversion of metal oxides to metals. Based on our previous research on direct reduction of CuO and NiO into the corresponding metals, herein, conversion of other metal oxides (Fe₂O₃, MnO₂, Co₃O₄, PbO₂) with glucose was investigated to illustrate the universal applicability of direct reduction of metal oxides with carbohydrates under alkali hydrothermal conditions. Furthermore, metal salt reduction by carbohydrates was studied and the reduction performance of glucose and cellulose with and without alkali was compared. The results showed an alkaline hydrothermal environment is more conducive to metal reduction. Unlike the complete reduction of CuO and NiO, oxides of Fe(III), Mn(IV), Co(III) and Pb(IV) can only be partially reduced under the experimental conditions. Not only carbohydrates but also decomposed intermediates can reduce metal oxides or salts. In addition, due to the formation of stable complexes between the anions of salts and the decomposition products of carbohydrates, the reduction effects of various copper salts are significantly different. This study may provide an alternative approach to metal preparation in hydrometallurgy.

Tropospheric ozone (O₃) enrichment caused by human activities can reduce important crop yields with huge economic loss and affect the global carbon cycle and climate change in the coming decades. In this study, two Italian cultivars of durum wheat (Claudio and Mongibello) were exposed to O₃ (80 ppb, 5 h day⁻¹ for 70 consecutive days), with the aim to investigate the changes in yield and biomass, ecophysiological traits, and stable carbon and nitrogen isotope values in plants, and to compare the stable isotope responses under environmental stressors. Both cultivars showed a relative O₃ tolerance in terms of photosynthetic performance, but in cultivar Mongibello, O₃ was detrimental to the grain yield and plant biomass. The δ¹³C values in the leaves of plants identified that the impact of O₃ on CO₂ fixation by RuBisCO was dominant. The δ¹⁵N value showed significant differences between treatments in both cultivars at seven days from the beginning of the exposure, which could be considered an early indicator of ozone pollution. Under increasingly frequent extreme climates globally, the relationships among stable isotope data, ecophysiological traits, and agronomic parameters could help breed future cultivars.

The wet oxidation of pharmaceutical sludge for the treatment and production of value-added materials was investigated. The experiments were carried out in a stainless-steel autoclave reactor with chemical synthetic pharmaceutical sludge. The highest removal rate of total suspended solids (90.1%) and volatile suspended solids (98.4%) was achieved at 260 °C for 60 min with an initial oxygen pressure of 0.8 MPa. Simultaneously, the total chemical oxygen demand removal rate (78.7%) and the soluble chemical oxygen demand removal rate (81.6%) were obtained. The volatile fatty acid concentration—including acetic acid, propanoic acid, isobutyric acid and isovaleric acid—increased to 4819 mg/L with pH 12.56, which indicated the possibility of improving the quality of wet oxidized sludge solution as a potential carbon source by adding reagents. Scanning electron microscopy images showed that the sludge became a loose porous structure after wet oxidation, which is beneficial for dewatering performance. Energy dispersive spectroscopy images illustrate that carbon elements in sludge migrate from solid to liquid phases during the wet oxidation process. These results provide meaningful data for the design of further works and demonstrate that wet oxidation is a promising method for the treatment of pharmaceutical sludge, and the produced volatile fatty acids, including acetic acid and propanoic acid, are potential carbon sources for the biological treatment of wastewater.

The treatment of antibiotic mycelial residue (AMR) has emerged as a critical challenge hindering the sustainable development of the biopharmaceutical industry. As a representative hazardous solid waste generated during antibiotic manufacturing processes, AMR may pose substantial risks to environmental safety. This review elucidates the properties and hazards of AMR while systematically reviewing current mainstream treatment technologies. Building upon the elucidation of underlying mechanisms, it further examines the application bottlenecks and research progress associated with different techniques. Through a comprehensive understanding of existing research achievements, this paper proposes future development strategies and perspectives for AMR treatment, highlighting that integrated multi-technology treatment approaches may represent the predominant developmental direction in this field.

Production of energy and chemicals from biomass resources has been regarded as one promising method to address the challenge of global warming. In this research, production of acrylic acid from fumaric acid, one of the biomass-derived building blocks, is proposed. CuO was employed as a solid oxidant, which showed excellent activity and selectivity for the production of acrylic acid, and water played an essential role in acting as not only a solvent but also a catalyst in this process. An optimum acrylic acid yield of 76.4% was successfully obtained after the reaction of fumaric acid with CuO at 300 °C for only 60 s.This research provides a green and highly efficient way to produce value-added chemicals from biomass-derived building blocks, and thus is promising for practical application.