Evgeniy Prikhodko

Prof. Dr. Evgeniy Prikhodko

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 April 2023 in Energies
Verified
Journal Article
Open access
PDF file
ANAlexandr Nikiforov
Alexandr Nikiforov
AKAkmaral Kinzhibekova
Akmaral Kinzhibekova
EPEvgeniy Prikhodko
Evgeniy Prikhodko
AKAmangeldy Karmanov
Amangeldy Karmanov
SNSholpan Nurkina
Sholpan Nurkina
One of the options for reducing harmful emissions in the production of heat energy is the use of biomass, including in combination with industrial waste (for instance, coal and coke dust). Recent studies demonstrate that a mix of biomass and coal makes it possible to obtain a bio-coal briquette with better characteristics, which is a motivating factor in the search for alternative sources of heat energy from local agricultural waste. The aim of this research is to study the properties of bio-coal briquettes from biomass (sunflower husks and leaves) and industrial waste (coal and coke dust). The raw material was grinded and used for the production of bio-coal briquettes of 20%, 30%, 40%, 50%, 60%, and 70% of biomass. The biomass was grinded to the size of no more than 2 mm for the fine fraction and no more than 6 mm for the coarse fraction. The briquettes were made mechanically using a hydraulic press with a compression pressure of 25 MPa without the use of any binder. The characteristics of the investigated bio-coal briquettes, such as density, strength, moisture content, ash content, volatile yield, calorific value, ignition time, burning duration, and burning rate, have good enough values. The fine fraction briquettes compared to the coarse fraction briquettes have a longer burning time (about threefold longer) and a lower burning rate. For all briquettes, an increase in the composition of coal dust results in a rise in the burning time, whereas the burning rate falls. The best in terms of strength, calorific value and combustion parameters are the following briquettes: 70% sunflower husk and 30% coal dust from the Karazhyra deposit; 60% sunflower husk and 40% coal dust from the Shubarkul deposit; briquettes from 70% sunflower husk and 30% coke dust; briquettes from 80% leaves and 20% coal dust from the Karazhyra deposit; and briquettes from 70% leaves and 30% coal dust from the Shubarkul deposit. The selected briquettes are suitable as an alternative source of fuel.

21 September 2023 in Energies
Verified
Journal Article
Open access
PDF file
EPEvgeniy Prikhodko
Evgeniy Prikhodko
ANAlexandr Nikiforov
Alexandr Nikiforov
AKAkmaral Kinzhibekova
Akmaral Kinzhibekova
APAlexandr Paramonov
Alexandr Paramonov
NANazgul Aripova
Nazgul Aripova
AKAmangeldy Karmanov
Amangeldy Karmanov
The energy efficiency of high-temperature batch aggregates largely depends on the modes of their heating and cooling. The modes of heating and cooling of aggregates in which thermal stress does not exceed the critical values of the ultimate strength of the refractories make it possible to increase their service life. The increase in the service life of refractories will lead to a reduction in the number of lining repairs and a decrease in the specific consumption of refractory materials per ton of technological product. Shorter warm-up and cool-down times result in lower energy consumption. Reducing the time for variable modes for casting ladles increases their turnover (the number of melt discharges into the ladle per day). Increasing ladle turnover not only reduces the number of ladles but also improves the economic performance of the enterprise. The ultimate strength of the refractory material significantly affects the rate of temperature change during heating and cooling of the refractory masonry. The purpose of this research is to study the dependence of the ultimate compression and tensile strengths of chamotte materials of the ShKU brand on temperature. The determination of the compression and tensile strengths was carried out on new samples of refractory materials as well as on samples of refractories that were in operation until the intermediate repair. To determine the ultimate compression strength of chamotte refractories, the standard technique for axial compression of the test specimen until its destruction was used. To determine the ultimate tensile strength, a three-point bending test was used with additional control of the surface temperature of the test sample during the test. The ultimate compression strength of chamotte refractories of the ShKU-32 brand increased for the new refractories by a maximum of 44%. For refractories that were in operation until the intermediate repair, the ultimate compression strength increased by a maximum of 56%. The value of the ultimate tensile strength at elevated temperatures turned out to be higher than the value at a temperature of 20 °C. For new refractories, the maximum ultimate tensile strength is 25% higher than the ultimate tensile strength under normal conditions. For refractories that were in operation until the intermediate repair, the maximum ultimate tensile strength increased by 24%. The obtained results can be used to increase the rate of heating or cooling of linings.

21 June 2024 in Energies
Verified
Journal Article
Open access
PDF file
ANAlexandr Nikiforov
Alexandr Nikiforov
EPEvgeniy Prikhodko
Evgeniy Prikhodko
AKAkmaral Kinzhibekova
Akmaral Kinzhibekova
AKAmangeldy Karmanov
Amangeldy Karmanov
Tatiana Alexiou IvanovaTatiana Alexiou Ivanova
Tatiana Alexiou Ivanova
The combustion of briquettes made from organic and industrial residues in small boilers requires researchers to consider the characteristics of this type of fuel and methods of its combustion. For the efficient combustion of fuel briquettes, a layered combustion method with the ability to regulate the supply of combustion air is better suited. The purpose of this research is to study the thermal technical conditions of briquetted fuel combustion. In order to carry this out, a stand was created, which made it possible to determine the combustion efficiency of this type of fuel. Two types of briquettes were studied: one with 30% sunflower husks and 70% leaves, and one with and 70% sunflower husks and 30% coke breeze. The combustion results of the briquettes show that heat loss from chemical under-burning was no more than 6.25%. To determine the temperature distribution in the fuel layer, a model of unsteady heat transfer in a fixed layer was used. A calculation of the temperature fields in the layer of burned fuel briquettes was carried out, which showed that the most favorable conditions for burning briquettes were created with a layer about 15–20 cm thick for both burned briquette options. The temperature was in the range of 450–750 °C, which on the one hand corresponds to experimental data and on the other hand provides a combustion regime that occurs with a relatively low loss to the environment. This installation and mathematical model will help future studies based on the processes of other types of organic waste combustion with a grate system.

4 March 2024 in Energies
Verified
Journal Article
Open access
PDF file
EPEvgeniy Prikhodko
Evgeniy Prikhodko
ANAlexandr Nikiforov
Alexandr Nikiforov
AKAkmaral Kinzhibekova
Akmaral Kinzhibekova
NANazgul Aripova
Nazgul Aripova
AKAmangeldy Karmanov
Amangeldy Karmanov
VRVladimir Ryndin
Vladimir Ryndin
An important element of the operation of high-temperature aggregates are modes that change over time. During these modes, maximum temperature changes are recorded in the cross-section of the lining of the aggregate. The difference in temperature leads to the formation of thermal stresses, which are the main reason for the repair of aggregates. During rapid heating, the inner layers of the lining are subjected to compressive stresses, while during rapid cooling, these layers experience tensile stresses. Under the same conditions, rapid cooling of the lining is more critical, since refractories have poor resistance to tension. The purpose of the study is to calculate and analyze the thermal stresses that arise during cooling of the casting ladle lining. The stresses are determined based on the calculation of the unsteady temperature field of the lining. Thermal stress values are necessary for analysis of the current cooling rates of casting ladles and subsequent development of optimal cooling modes for the lining. To solve the heat conductivity equation, a numerical method was chosen using an implicit four-point difference scheme. To study the cooling process of the casting ladle lining, temperature measurements were carried out in the zone of the greatest wear of the lining. Under conditions of natural convection, cooling of the casting ladle lining occurs unevenly. Cooling schedules during natural convection are characterized by significant unevenness and high rates of temperature decrease. The cooling rates of the inner surface of the lining at the initial stage of cooling significantly exceed the values recommended in the technical literature. Such cooling rates lead to the appearance of significant thermal stresses in the lining. For a refractory that has not been in service, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.27 times, and the tensile stresses exceed the corresponding limit values by 4.4 times. For refractories that have worked three fuses in the ladle lining, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.28 times, and the tensile stresses exceed the corresponding limit values by 3.19 times. The studied cooling modes for the casting ladle lining are unacceptable for operation. Cooling, taking into account the indicated rates, leads to the destruction of the lining material. To increase the resistance and duration of the working campaign of casting ladle linings, it is necessary to develop cooling modes for the lining at speeds at which the resulting thermal stresses do not exceed the strength of the refractory materials.

30 September 2022 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
SNSholpan Nurkina
Sholpan Nurkina
AKAkmaral Kinzhibekova
Akmaral Kinzhibekova
EPEvgeniy Prikhodko
Evgeniy Prikhodko
The article is devoted to the actual problem of utilisation of agricultural and industrial waste as a solution to the problem of replacing traditional energy sources. As an alternative fuel, researchers suggest using briquettes from biomass (leafy debris, waste paper, sunflower and buckwheat husks), as well as their combination with industrial waste (coal dust). The choice of these sources of raw materials is determined by their presence in the north-eastern part of Kazakhstan. Studies of the physical and mechanical and thermophysical characteristics of fuel briquettes from organic mass and bio-charcoal briquettes were carried out. The studies showed the following results: the moisture content of the samples we studied lies in the range from 3.86 to 8 %; ash content of briquettes from vegetable raw materials varies from 2.05 % to 3.6 %, combined briquettes from foliage and coal dust varies from 10 % to 14 %; average density values varies from 979.91 to 1172.63 kg/m3; mechanical strength is in the range from 90 to 100 %; the yield of volatile studied samples ranges from 9 to 21.4 %. Analysis of the obtained characteristics of fuel briquettes demonstrated that they meet the requirements of existing standards. Herewith, the lower calorific value of briquettes (15290‑19048 kJ/kg) is comparable to the calorific value of coal from the Ekibastuz deposit. The authors studied the influence of the parameters of the briquetting process on the briquette’s strength characteristics from leaves and waste paper, and obtained a regression dependence of these briquette’s calorific value on their characteristics. The analysis of regression dependencies showed that the pressure and pressing time have the greatest influence on the briquette strength, and its composition, i.e., the ratio of leaves and waste paper in the feedstock, has the greatest influence on the lower calorific value

29 January 2018 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
ANA S Nikiforov
A S Nikiforov
EPEvgeniy Prikhodko
Evgeniy Prikhodko
AKA K Kinzhibekova
A K Kinzhibekova
AKA E Karmanov
A E Karmanov
One of the main reasons for the withdrawal of high-temperature aggregates for repairs is the destruction of enclosing structures due to the occurrence of temperature stresses. A wide range of refractory materials used, a large number of product names, a difference in the operation of even the same aggregates makes it impossible to apply general principles for determining the residual resource of high-temperature aggregates, which is based, as a rule, on the determination of temperature stresses. In the article there is suggested a technique based on the method of simulation modeling, allowing to estimate the remaining resource and reliability of the operating equipment. There are given data on the calculation of these indicators for a 25-ton steel-casting ladle. The values obtained make it possible to evaluate the rationality of the further operation of the high-temperature unit by the condition of reliability of the enclosing structures.