An important element of the operation of high-temperature aggregates are modes that change over time. During these modes, maximum temperature changes are recorded in the cross-section of the lining of the aggregate. The difference in temperature leads to the formation of thermal stresses, which are the main reason for the repair of aggregates. During rapid heating, the inner layers of the lining are subjected to compressive stresses, while during rapid cooling, these layers experience tensile stresses. Under the same conditions, rapid cooling of the lining is more critical, since refractories have poor resistance to tension. The purpose of the study is to calculate and analyze the thermal stresses that arise during cooling of the casting ladle lining. The stresses are determined based on the calculation of the unsteady temperature field of the lining. Thermal stress values are necessary for analysis of the current cooling rates of casting ladles and subsequent development of optimal cooling modes for the lining. To solve the heat conductivity equation, a numerical method was chosen using an implicit four-point difference scheme. To study the cooling process of the casting ladle lining, temperature measurements were carried out in the zone of the greatest wear of the lining. Under conditions of natural convection, cooling of the casting ladle lining occurs unevenly. Cooling schedules during natural convection are characterized by significant unevenness and high rates of temperature decrease. The cooling rates of the inner surface of the lining at the initial stage of cooling significantly exceed the values recommended in the technical literature. Such cooling rates lead to the appearance of significant thermal stresses in the lining. For a refractory that has not been in service, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.27 times, and the tensile stresses exceed the corresponding limit values by 4.4 times. For refractories that have worked three fuses in the ladle lining, the maximum thermal compressive stresses exceed the ultimate compressive strength by 1.28 times, and the tensile stresses exceed the corresponding limit values by 3.19 times. The studied cooling modes for the casting ladle lining are unacceptable for operation. Cooling, taking into account the indicated rates, leads to the destruction of the lining material. To increase the resistance and duration of the working campaign of casting ladle linings, it is necessary to develop cooling modes for the lining at speeds at which the resulting thermal stresses do not exceed the strength of the refractory materials.
The purpose of the article is to select the cam profile (with equal design parameters) for driving the plunger of a high-pressure pump that provides the maximum speed and permissible acceleration of the pusher. A method of selecting a cam profile by analyzing combined graphs of changes in the path, speed, and acceleration of a cam pusher of various profiles using the Mathcad program is proposed. Calculations have been performed and combined graphs of changes in the path, speed, and acceleration of the cam pusher with tangential, convex, and concave profiles have been constructed. A comparative analysis of the combined graphs showed that the maximum speed of the cam pusher with a concave profile is 1,5 times greater than for cams with a tangential or convex profile. A cam with a concave profile is recommended for driving pump plungers of low-speed marine diesel engines (up to 250 min–1). To create ultra–high pressures (more than 120 MPa), the fuel supply system must be batterytype with a drive of small diameter plungers (4–6 mm) from an eccentric shaft with a special-shaped washer and electronically controlled injectors.
17 April 2015 in Russian Internet Journal of Industrial Engineering
The principle of an invariableness of designations of the basic quantities (30-40 quantities) is the basis for uniform system of letter designations of quantities which should not have synonymous (reserve) designations and must to be used strictly in all disciplines. The table of designations of such main quantities are given. At the same time symbols of the basic quantities are polysemantic and can be used for designation of quantities which were not included into the table of the main quantities. The polysemantic term "amount of substance" is offered to replace by unambiguous term "molarity of substance" or in abbreviated form "molarity" and to input a uniform symbol for this quantity.
The refractory lining of high-temperature aggregates determines the duration of their operation before major repairs. The ability to retain technological material within the aggregate’s working area is the main factor for its continued operation. The analysis shows that the main reason for the destruction of the lining of ferroalloy production casting ladles is the occurrence of thermal stresses in the processes of heating and cooling the lining. When the stresses exceed the ultimate strength of the refractory material used, the material is destroyed. The greater the magnitude and duration of the excess thermal stresses, the faster the lining destruction occurs. Streamlining thermal regimes is the most low-cost and sufficiently effective way to increase the durability of linings. The development of lining heating and cooling regimes can be carried out on the basis of determining the thermal stress state by calculating the maximum permissible heating rates. The developed regimes allow for working at speeds at which the resulting stresses do not exceed the ultimate strength of the refractory materials. The aim of this study is to develop efficient cooling regimes for the lining of a ferroalloy production casting ladle from the standpoint of the resulting thermal stresses. A method for determining the thermal stresses in the lining has been developed and implemented using Microsoft Excel. This facilitates the use of the developed methodology in production without the need for special skills on the part of operating personnel. Using the developed methodology, the cooling schedules for the lining of ferroalloy production ladles were improved. To reduce temperature unevenness across the lining cross-section, a decision was made to initially heat the outer surface of the lining and cool the inner surface of the lining. Heating the outer surface can be achieved by using the heat of combustion of the ferroalloy gas or the heat of the exhaust gases from the stand for drying and heating casting ladles. Cooling the inner surface of the lining can be achieved by natural convection. The result of the development and implementation of an efficient cooling regime is a reduction in thermal stresses to the required level throughout almost the entire cooling process.
Classical thermodynamics traditionally overlooks the role of quantities dependent on spatial coordinates and time, especially in the context of unsteady flows. This research introduces the first law of thermodynamics (FLT) tailored for non-stationary flow, distinguishing itself with the inclusion of terms bearing partial derivatives of pressure, p(x, t), concerning coordinates and time (–υ(∂р/∂х)dx; –υ(∂р/∂t)dt). By employing this novel approach, the derived equations are validated using a centred compression wave as a representative non-stationary flow case study. A methodology is also presented for experimentally quantifying hydrodynamic energy losses in the intake and exhaust systems of internal combustion engines. Central to the exploration is the calculation of pressure forces' work –υ(∂р/∂х)dx and –υ(∂р/∂t)dt) in the FLT equation for non-stationary flows, particularly their applicability to a centred compression wave. Moreover, a distinct procedure for discerning friction work in non-stationary flow is delineated. The research methods encompass both analytical derivation and numerical simulations leveraging Mathcad software. The bespoke Mathcad program crafted for this study can graphically represent multiple flow parameters as functions of time, proving invaluable for comprehending compression wave dynamics and evaluating friction work in diverse non-steady flows. Ultimately, the incorporation of energy equations tailored for non-stationary flows into classical thermodynamics paves the way for a more comprehensive understanding and application of thermodynamics to intricate flow scenarios.
30 September 2026 in Kazakhstan journal for oil & gas industry
Background: Polymer flooding remains one of the most technically viable enhanced oil recovery methods for mature fields in Kazakhstan’s Pre-Caspian Basin. Predicting its sweep efficiency in heterogeneous carbonate reservoirs is challenging due to complex pore-throat geometry, high-salinity formation waters, and pronounced permeability contrasts. Conventional reservoir simulation is computationally prohibitive for real-time operational decisions and probabilistic uncertainty analysis. Aim: This study develops and validates a hybrid surrogate framework integrating gradient boosting regression with physics-informed constraints derived from polymer transport theory to predict incremental oil recovery factor and injectivity ratio for polymer flooding in carbonate formations of the Pre-Caspian Basin. Materials and Methods: A dataset of 412 polymer flooding operations was compiled from published literature, Society of Petroleum Engineers (SPE) technical reports, and internal field data from three Kazakhstani assets: Tengizchevroil, Karachaganak Petroleum Operating, and the Uzen field operated by Ozenmunaigas. Eighteen reservoir and fluid parameters were used as input features. Gradient boosting regression was trained using a stratified 80/20 split with five-fold cross-validation. Physics-informed penalty terms derived from Darcy-scale polymer transport equations were embedded in the loss function to ensure physical consistency. Model performance was benchmarked against artificial neural networks, support vector regression, and full compositional simulation. Results: The physics-informed gradient boosting model achieved a coefficient of determination R² = 0.924 and root mean square error of 2.31% on the held-out test set for recovery factor prediction, outperforming artificial neural networks (R² = 0.891) and support vector regression (R² = 0.857). The physics penalty reduced physically inconsistent predictions by 78%. SHapley Additive exPlanations (SHAP) analysis identified the permeability variation coefficient, polymer concentration, and formation water salinity as dominant predictors. Surrogate estimates agreed with full compositional simulation within ±1.8% absolute for the Uzen carbonate pilot. Conclusions: The proposed surrogate model provides rapid and reliable predictions of polymer flooding performance suitable for field-scale integration, substantially reducing computational burden for enhanced oil recovery screening and optimization in heterogeneous carbonate reservoirs of Kazakhstan.